Infiniti G35 (V35). Manual — part 682
PS-38
SERVICE DATA AND SPECIFICATIONS (SDS)
Steering Gear
NGS0001G
Oil Pump
NGS0001H
Steering Fluid
NGS0001I
Inner socket length“ L”
106.3 mm (4.19 in)
STC1030D
Rack neutral position, dimension “L” (rack stroke)
64.5 mm (2.539 in)
SGIA0629J
Oil pump relief hydraulic pressure
9,600 - 10,200 kPa (97.9 - 104 kg/cm
2
, 1,392 - 1,479 psi)
Fluid capacity
Approx. 1.0
(1-1/8 US qt, 7/8 Imp qt)
RAX-1
REAR AXLE
D DRIVELINE/AXLE
CONTENTS
C
E
F
G
H
I
J
K
L
M
SECTION
A
B
RAX
REAR AXLE
PRECAUTIONS . . . . . . . . . . . . . . .. 2
Caution . . . . . . . . . . . . . . . . . . 2
PREPARATION . . . . . . . . . . . . . . ... 3
Special Service Tools . . . . . . . . . . . ... 3
Commercial Service Tools . . . . . . . . . . 4
NOISE, VIBRATION AND HARSHNESS (NVH)
TROUBLESHOOTING . . . . . . . . . . . . 5
NVH Troubleshooting Chart . . . . . . . . . . 5
WHEEL HUB . . . . . . . . . . . . . . . .. 6
On-Vehicle Inspection . . . . . . . . . . . .. 6
WHEEL BEARING INSPECTION . . . . . . . 6
Removal and Installation . . . . . . . . . . .. 6
INSTALLATION . . . . . . . . . . . . . . 7
Disassembly and Assembly . . . . . . . . . .. 7
REAR DRIVE SHAFT . . . . . . . . . . . ... 10
Removal and Installation . . . . . . . . . . 10
Disassembly and Assembly . . . . . . . . . 11
SERVICE DATA AND SPECIFICATIONS (SDS) . .. 16
Wheel Bearing . . . . . . . . . . . . . . 16
Drive Shaft . . . . . . . . . . . . . . . .. 16
RAX-2
PRECAUTIONS
PRECAUTIONS
PFP:00001
Caution
NDS0001Z
Observe the following precautions when disassembling and servicing drive shaft.
●
Joint sub-assembly does not disassemble because it is non-overhaul parts.
●
Perform work in a location which is as dust-free as possible.
●
Before disassembling and servicing, clean the outside of parts.
●
Prevention of the entry of foreign objects must be taken into account during disassembly of the service
location.
●
Disassembled parts must be carefully reassembled in the correct order. If work is interrupted, a clean
cover must be placed over parts.
●
Paper shop cloths must be used. Fabric shop cloths must not be used because of the danger of lint adher-
ing to parts.
●
Disassembled parts (except for rubber parts) should be cleaned with kerosene which shall be removed by
blowing with air or wiping with paper shop cloths.
PREPARATION
RAX-3
C
E
F
G
H
I
J
K
L
M
A
B
RAX
PREPARATION
PFP:00002
Special Service Tools
NDS00020
The actual shapes of Kent-Moore tools may differ from those of special service tools illustrated here.
Tool number
(Kent-Moore No.)
Tool name
Description
ST33220000
( — )
Drift
a: 37 mm (1.46 in) dia.
b: 31 mm (1.22 in) dia.
c: 22 mm (0.87 in) dia.
●
Removing wheel hub
●
Removing wheel bearing outer side
inner race
●
Inspection of wheel bearing rotating
torque
ST33251000
( — )
Drift
Installing wheel hub
ST35300000
( — )
Drift
a: 45 mm (1.77 in) dia.
b: 59 mm (2.32 in) dia.
●
Installing wheel hub
●
Inspection of wheel bearing rotating
torque
KV40100900
( — )
Drift
a: 52 mm (2.05 in) dia.
b: —
Wheel bearing rotating torque inspection
KV38100500
( — )
Drift
a: 80 mm (3.15 in) dia.
b: 60 mm (2.36 in) dia.
Installing drive shaft plug
KV38102200
( — )
Drift
a: 90 mm (3.54 in) dia.
b: 31 mm (1.22 in) dia.
Installing drive shaft plug
ZZA1046D
ZZA0982D
ZZA0881D
ZZA0539D
ZZA0701D
ZZA0920D
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст