Infiniti G35 (V35). Manual — part 240
TROUBLE DIAGNOSIS
BRC-21
[VDC/TCS/ABS]
C
D
E
G
H
I
J
K
L
M
A
B
BRC
TFWM0142E
BRC-22
[VDC/TCS/ABS]
TROUBLE DIAGNOSIS
TFWM0143E
TROUBLE DIAGNOSIS
BRC-23
[VDC/TCS/ABS]
C
D
E
G
H
I
J
K
L
M
A
B
BRC
Control Unit Input/Output Signal Standard
NFS0006X
REFERENCE VALUE FROM CONSULT-II
CAUTION:
Items displayed are data calculated by control unit and may indicate normal operation even if output
circuit (harness) is open or shorted.
Monitor item
Contents
DATA MONITOR
Condition
Reference value in nor-
mal operation
SLCT LVR POSI
Shift position determined by the A/T PNP
switch signal
Indicate each shift position
(M/T models normally remain at ##)
GEAR
Gear position determined by TCM
1:1st gear (M/T models: normally remain at 1)
2:2nd gear
3:3rd gear
4:4th gear
5:5th gear
FR LH SENSOR
FR RH SENSOR
RR LH SENSOR
RR RH SENSOR
Wheel speed
Vehicle stopped
0 [km/h (MPH)]
Vehicle running (Note 1)
Almost in accordance
with speedometer dis-
play (within
±
10 %)
ACCEL POS SIG
Throttle actuator opening/closing is dis-
played (linked with accelerator pedal).
Accelerator pedal not depressed
(Engine stopped)
0 %
Depress accelerator pedal
(Engine stopped)
0 - 100 %
ENGINE RPM
With engine running
With engine stopped
0 rpm
Engine running
Almost in accordance
with tachometer display
STR ANGLE SIG
Steering angle detected by steering
angle sensor
Straight-ahead
Approx. 0
°
Steering wheel turned
–720 to 720
°
YAW RATE SEN
Yaw rate detected by yaw rate sensor
Vehicle stopped
Approx. 0 d/s
Vehicle running
–70 to 70 d/s
SIDE G SENSOR
Transverse G detected by side G sensor
Vehicle stopped
Approx. 0 m/s
2
Vehicle running
–24.3 to 24.1 m/s
2
PRESS SENSOR
Brake fluid pressure detected by pres-
sure sensor
With ignition switch turned ON and
brake pedal released
Approx. 0 bar
With ignition switch turned ON and
brake pedal depressed
–40 to 300 bar
BATTERY VOLT
Battery voltage supplied to VDC/TCS/
ABS control unit
Ignition switch ON
10 - 16 V
STOP LAMP SW
Brake pedal operation
Brake pedal depressed
ON
Brake pedal not depressed
OFF
PARK BRAKE SW
Parking brake condition
Parking brake operated
ON
Parking brake not operated
OFF
OFF SW
VDC OFF switch ON/OFF condition
VDC OFF switch ON
(When VDC OFF indicator lamp is ON)
ON
VDC OFF switch OFF
(When VDC OFF indicator lamp is
OFF)
OFF
ABS WARN LAMP
ABS warning lamp ON condition (Note 2)
ABS warning lamp ON
ON
ABS warning lamp OFF
OFF
BRC-24
[VDC/TCS/ABS]
TROUBLE DIAGNOSIS
Note 1: Confirm tire pressure is normal.
Note 2: ON/OFF timing of warning lamp and indicator lamp. Refer to
BRC-33, "INSPECTION OF ABS WARNING LAMP, VDC OFF
INDICATOR LAMP, SLIP INDICATOR LAMP AND BRAKE WARNING LAMP"
MOTOR RELAY
Operation condition of motor and motor
relay
When motor relay and motor are
operating
ON
When motor relay and motor are not
operating
OFF
ACTUATOR RLY
Solenoid valve relay operation condition
When solenoid valve relay is operating
ON
When solenoid valve relay is not operat-
ing
OFF
OFF LAMP
VDC OFF indicator lamp condition
(Note 2)
When VDC OFF indicator lamp is ON
ON
When VDC OFF indicator lamp is OFF
OFF
SLIP LAMP
SLIP indicator lamp condition (Note 2)
When SLIP indicator lamp is ON
ON
When SLIP indicator lamp is OFF
OFF
IN ABS S/V
OUT ABS S/V
Solenoid valve operation
Actuator (solenoid) is active (“ACTIVE
TEST” with CONSULT-II) or solenoid
valve relay is inactive (in fail-safe
mode).
ON
When actuator (solenoid) is not active
and solenoid valve relay is active (igni-
tion switch ON).
OFF
USV
HSV
VDC switch-over valve condition
When actuator (switch-over valve) is
active (“ACTIVE TEST” with CONSULT-
II) or actuator relay is inactive (when in
fail-safe mode).
ON
When actuator (switch-over valve) is not
active and actuator relay is active (igni-
tion switch ON).
OFF
V/R OUTPUT
Actuator relay activated
(ON/OFF)
When actuator relay is active (engine is
running).
ON
When actuator relay is not active
(before engine starts and in fail-safe
mode).
OFF
M/R OUTPUT
Actuator motor and motor relay condition
(ON/OFF)
When actuator motor and motor relay
are active (“ACTIVE TEST” with CON-
SULT-II).
ON
When the actuator motor and motor
relay are not operating
OFF
FLUID LEV SW
Brake fluid level switch ON/OFF condi-
tion.
When brake fluid level switch ON
ON
When brake fluid level switch OFF
OFF
FAIL SIGNAL
Fail signal condition
VDC fail
TCS fail
ABS fail
EBD fail
OFF
Monitor item
Contents
DATA MONITOR
Condition
Reference value in nor-
mal operation
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст