Infiniti G35 (V35). Manual — part 431
DTC P2127, P2128 APP SENSOR
EC-605
C
D
E
F
G
H
I
J
K
L
M
A
EC
12.
CHECK APP SENSOR
Refer to
EC-605, "Component Inspection"
OK or NG
OK
>> GO TO 14.
NG
>> GO TO 13.
13.
REPLACE ACCELERATOR PEDAL ASSEMBLY
1.
Replace accelerator pedal assembly.
2.
Perform
EC-79, "Accelerator Pedal Released Position Learning"
3.
Perform
EC-79, "Throttle Valve Closed Position Learning"
4.
Perform
EC-79, "Idle Air Volume Learning"
>> INSPECTION END
14.
CHECK INTERMITTENT INCIDENT
Refer to
EC-151, "TROUBLE DIAGNOSIS FOR INTERMITTENT INCIDENT"
>> INSPECTION END
Component Inspection
NBS00110
ACCELERATOR PEDAL POSITION SENSOR
1.
Reconnect all harness connectors disconnected.
2.
Turn ignition switch ON.
3.
Check voltage between ECM terminals 106 (APP sensor 1 sig-
nal), 98 (APP sensor 2 signal) and ground under the following
conditions.
4.
If NG, replace accelerator pedal assembly and go to next step.
5.
Perform
EC-79, "Accelerator Pedal Released Position Learning"
6.
Perform
EC-79, "Throttle Valve Closed Position Learning"
7.
Perform
EC-79, "Idle Air Volume Learning"
Removal and Installation
NBS00111
ACCELERATOR PEDAL
Refer to
ACC-3, "ACCELERATOR CONTROL SYSTEM"
Terminal
Accelerator pedal
Voltage
106
(Accelerator pedal position
sensor 1)
Fully released
0.5 - 1.0V
Fully depressed
3.9 - 4.7V
98
(Accelerator pedal position
sensor 2)
Fully released
0.15 - 0.60V
Fully depressed
1.95 - 2.40V
MBIB0023E
EC-606
DTC P2135 TP SENSOR
DTC P2135 TP SENSOR
PFP:16119
Component Description
NBS00112
Electric throttle control actuator consists of throttle control motor,
throttle position sensor, etc. The throttle position sensor responds to
the throttle valve movement.
The throttle position sensor has two sensors. These sensors are a
kind of potentiometers which transform the throttle valve position into
output voltage, and emit the voltage signal to the ECM. In addition,
these sensors detect the opening and closing speed of the throttle
valve and feed the voltage signals to the ECM. The ECM judges the
current opening angle of the throttle valve from these signals and the
ECM controls the throttle control motor to make the throttle valve
opening angle properly in response to driving condition.
CONSULT-II Reference Value in Data Monitor Mode
NBS00113
Specification data are reference values.
*: Throttle position sensor 2 signal is converted by ECM internally. Thus, it differs from ECM terminal voltage signal.
On Board Diagnosis Logic
NBS00114
This self-diagnosis has the one trip detection logic.
FAIL-SAFE MODE
When the malfunction is detected, the ECM enters fail-safe mode and the MIL lights up.
PBIB0145E
MONITOR ITEM
CONDITION
SPECIFICATION
THRTL SEN 1
THRTL SEN 2*
●
Ignition switch: ON
(Engine stopped)
●
Shift lever: D (A/T) or 1st (M/T)
Accelerator pedal: Fully released
More than 0.36V
Accelerator pedal: Fully depressed
Less than 4.75V
DTC No.
Trouble diagnosis name
DTC detecting condition
Possible cause
P2135
2135
Throttle position sensor
circuit range/perfor-
mance
Rationally incorrect voltage is sent to ECM
compared with the signals from TP sensor 1
and TP sensor 2.
●
Harness or connector
(The TP sensor 1 and 2 circuit is open or
shorted.)
(The APP sensor 2 circuit is shorted.)
●
Electric throttle control actuator
(TP sensor 1 and 2)
●
Accelerator pedal position sensor
(APP sensor 2)
Engine operation condition in fail-safe mode
ECM controls the electric throttle control actuator in regulating the throttle opening in order for the idle position to be within +10
degrees.
ECM regulates the opening speed of the throttle valve to be slower than the normal condition.
So, the acceleration will be poor.
DTC P2135 TP SENSOR
EC-607
C
D
E
F
G
H
I
J
K
L
M
A
EC
DTC Confirmation Procedure
NBS00115
NOTE:
If DTC Confirmation Procedure has been previously conducted, always turn ignition switch OFF and wait at
least 10 seconds before conducting the next test.
TESTING CONDITION:
Before performing the following procedure, confirm that battery voltage is more than 8V at idle.
WITH CONSULT-II
1.
Turn ignition switch ON.
2.
Select “DATA MONITOR” mode with CONSULT-II.
3.
Start engine and let it idle for 1 second.
4.
EC-609, "Diagnostic Procedure"
.
WITH GST
Follow the procedure “WITH CONSULT-II” above.
SEF058Y
EC-608
DTC P2135 TP SENSOR
Wiring Diagram
NBS00116
TBWM0829E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст