Infiniti G35 (V35). Manual — part 617
LT-148
INTERIOR ROOM LAMP
6.
CHECK IGNITION KEY HOLE ILLUMINATION CIRCUIT
1.
Disconnect BCM connector and key hole illumination connector.
2.
Check continuity between BCM harness connector M2 terminal
41 and key hole illumination harness connector M309 terminal
1.
OK or NG
OK
>> Replace BCM if ignition key hole illumination does not
work after setting the connector again. Refer to
"Removal and Installation of BCM"
.
NG
>> Repair harness or connector.
All Step Lamps Does Not Operate
NKS002PW
1.
CHECK EACH DOOR SWITCH
Select “BCM” on CONSULT-II. With “INT LAMP” data monitor to
make sure switches listed below turn ON-OFF linked with switch
operation.
OK or NG
OK
>> GO TO 2.
NG
>> Inspect malfunctioning switch system.
2.
CHECK STEP LAMP INPUT
1.
Turn ignition switch OFF.
2.
Check voltage between step lamp (driver side) harness connec-
tor D10 terminal 1 and ground.
OK or NG
OK
>> GO TO 3.
NG
>> GO TO 4.
3.
CHECK STEP LAMP CIRCUIT
1.
Disconnect BCM connector and front door driver side step lamp
connector.
2.
Check continuity between BCM harness connector M2 terminal
47 and step lamp (driver side) harness connector D10 terminal
2.
OK or NG
OK
>> Replace BCM if step lamps does not work after setting
NG
>> Repair harness or connector.
41 – 1
: Continuity should exist.
PKIA5811E
Switch name
CONSULT screen
Driver side door switch
DOOR SW - DR
Passenger side door switch
DOOR SW - AS
PKIB3532E
1 – Ground
: Battery voltage
SKIA5949E
47 – 2
: Continuity should exist.
SKIA5950E
INTERIOR ROOM LAMP
LT-149
C
D
E
F
G
H
I
J
L
M
A
B
LT
4.
CHECK STEP LAMP CIRCUIT
1.
Disconnect BCM connector and step lamp connector.
2.
Check continuity between BCM harness connector M2 terminal
41 and step lamp (driver side) harness connector D10 terminal
1.
OK or NG
OK
>> Replace BCM if step lamps does not work after setting
the connector again. Refer to
NG
>> Repair harness or connector.
All Interior Room Lamps Does Not Operate
NKS002PX
1.
CHECK POWER SUPPLY CIRCUIT
1.
All interior room lamps switch are OFF.
2.
Turn ignition switch ON.
3.
Check voltage between BCM harness connector M2 terminal 41
and ground.
OK or NG
OK
>> Repair harness or connector. In a case of making a
short circuit, be sure to disconnect battery negative
cable after repairing harness, and then reconnect.
NG
>> Replace BCM. Refer to
BCS-16, "Removal and Installa-
Bulb Replacement
NKS002PY
VANITY MIRROR LAMP
1.
Insert a thin screwdriver in the lens end and remove lens.
2.
Remove bulb together with substrate.
3.
Installation is the reverse order of removal.
MAP LAMP
1.
Insert a small screwdriver into the lens hinge gap and remove
lens.
2.
Remove bulb.
3.
Installation is the reverse order of removal.
41 – 1
: Continuity should exist.
SKIA5951E
41 – Ground
: Battery voltage
SKIA5952E
Vanity mirror lamp
: 12 V - 1.32 W
PKIA1137E
Map lamp
: 12 V - 8 W
PKIA1131E
LT-150
INTERIOR ROOM LAMP
STEP LAMP
1.
Remove step lamp. Refer to
.
2.
Remove bulb.
3.
Installation is the reverse order of removal.
TRUNK ROOM LAMP
1.
Unfold pawl A and remove lens.
2.
Remove trunk room lamp while pressing pawl B in the direction
of the arrow.
3.
Disconnect trunk room lamp connector.
4.
Installation is the reverse order of removal.
IGNITION KEY HOLE ILLUMINATION
Without Intelligent Key System
1.
Remove cluster lid A and steering lock escutcheon. Refer to
10, "INSTRUMENT PANEL ASSEMBLY"
.
2.
Pull out ring, turn bulb socket to left to release lock and remove
it.
3.
Installation is the reverse order of removal.
With Intelligent Key System
1.
Remove instrument lower driver panel. Refer to
2.
Turn bulb socket to left to release lock and remove it.
Step lamp
: 12 V - 5 W
PKIA1126E
Trunk room lamp
: 12 V - 3.4 W
PKIA0182E
Ignition key hole illumination
: 12 V - 1.4 W
PKIA1134E
Ignition key hole illumination
: 12 V - 1.4 W
PKIB6108E
INTERIOR ROOM LAMP
LT-151
C
D
E
F
G
H
I
J
L
M
A
B
LT
Removal and Installation
NKS002PZ
MAP LAMP
Removal
1.
Insert a clip driver or a suitable tool and disengage the pawl fit-
tings of the map lamp.
2.
Disconnect connector and remove map lamp.
Installation
Installation is the reverse order of removal.
STEP LAMP
Removal
1.
Remove clips which are lower part of front door finisher and lift
finisher up.
2.
Disconnect step lamp connector.
3.
Press pawl on reverse side and remove the step lamp.
Installation
Installation is the reverse order of removal.
TRUNK ROOM LAMP
Removal
1.
Unfold pawl A and remove lens.
2.
Remove trunk room lamp while pressing pawl B in the direction
of the arrow.
3.
Disconnect trunk room lamp connector.
4.
Installation is the reverse order of removal.
Installation
Installation is the reverse order of removal.
PKIA1892E
PKIA1126E
PKIA0182E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст