Infiniti G35 (V35). Manual — part 557
IP-10
INSTRUMENT PANEL ASSEMBLY
INSTRUMENT PANEL ASSEMBLY
PFP:68200
Component Parts Drawing
NIS000HC
PIIB2701E
INSTRUMENT PANEL ASSEMBLY
IP-11
C
D
E
F
G
H
J
K
L
M
A
B
IP
Removal and Installation
NIS000HD
WORK STEP
When removing instrument panel and pad, cluster lid C assembly, cluster lid A assembly, center console
assembly, glove box assembly and center box assembly, take steps in the order shown by the numbers below.
1.
Defroster grille (RH)
2.
Defroster grille (LH)
3.
Display & A/C auto amp
4.
Cluster lid finisher upper
5.
Cluster lid finisher lower
6.
Instrument panel & pad
7.
Cluster lid A assembly
8.
Steering lock escutcheon
9.
Instrument finisher A
10. Side ventilator grille (LH)
11.
Steering column cover upper
12. Steering column cover lower
13. Steering column cover front lower
14. Knee protector lower
15. Instrument driver lower panel
16. Center ventilator grille (LH)
17. Instrument side panel (LH)
18. Cluster lid C side finisher (LH)
19. Cluster lid C assembly
20. Center console assembly
21. Console finisher assembly
22. Cluster lid C side finisher (RH)
23. Instrument lower cover
24. Glove box striker
25. Glove box assembly
26. Instrument side panel (RH)
27. Center box assembly
28. Instrument finisher B
29. NAVI control unit
30. Passenger air bag module
Parts
Refer-
ence
page
Instrument
panel &
pad
Cluster lid
C
assembly
Cluster lid
A
assembly
Center
console
assembly
Glove box
assembly
Center box
assembly
A
Selector lever knob (A/T models)
1
1
1
1
B
Shift knob (M/T models)
1
1
1
1
C
Console finisher (A/T models)
2
2
2
2
D
Console boot (M/T models)
2
2
2
2
E
Cluster lid C side finisher (RH/LH)
3
3
3
3
F
Cluster lid finisher upper
4
4
G
Cluster lid finisher lower
5
5
H
Instrument finisher B
6
6
4
I
Cluster lid C assembly
7
7
J
Instrument driver lower panel
8
1
K
Steering column covers
9
2
L
Lighting & turn signal switch
10
3
M
Wiper & washer switch
11
4
N
Knee protector lower
12
5
O
Steering lock escutcheon
13
6
P
Cluster lid A assembly
14
7
Q
Kicking plate (RH/LH)
15
1
5
R
Dash side finisher (RH/LH)
16
2
6
S
Instrument lower cover
17
3
7
T
Glove box assembly
18
4
8
U
Instrument side panel (RH/LH)
19
9
V
Center box assembly
20
10
W
NAVI control unit
21
X
Passenger air bag module
22
Y
Center console assembly
23
Z
Display & A/C auto amp
24
Aa
Defroster grille (RH/LH)
25
Ab
Side ventilator grille (LH)
26
Ac
Center ventilator grille (LH)
27
IP-12
INSTRUMENT PANEL ASSEMBLY
REMOVAL
(A) Selector lever Knob (A/T Models)
Remove selector lever knob. Refer to
AT-213, "Control Device Removal and Installation"
(B) Shift Knob (M/T Models)
.
(C) Console Finisher (A/T Models)
1.
Put selector lever in drive position.
2.
Remove clips from rear of console finisher, then remove clips at
front. Pull console finisher upward to disengage from console.
CAUTION:
Guide pin inserted into A/T device guide can be easily bro-
ken. Be careful when removing it.
3.
Disconnect harness connectors, and remove console finisher.
4.
After removing, remove each parts from console finisher.
(D) Console Boot (M/T Models)
1.
Insert a thin flat-bladed screwdriver wrapped with tape from behind console boot, and remove metal clip
on back. Then pull up and back to disengage from front metal clip.
2.
Disconnect hazard switch harness connector, and remove console boot.
(E) Cluster Lid C Side Finisher (RH/LH)
1.
Remove screws.
2.
Disconnect pawls, and remove cluster lid C side finisher.
(F) Cluster Lid Finisher Upper
Pull to the backside, disconnect clips and pawls, and remove cluster
lid finisher upper.
Ad
Front pillar garnish
28
Ae
Instrument panel & pad
29
Parts
Refer-
ence
page
Instrument
panel &
pad
Cluster lid
C
assembly
Cluster lid
A
assembly
Center
console
assembly
Glove box
assembly
Center box
assembly
PIIB2702E
PIIB2703E
PIIB2704E
INSTRUMENT PANEL ASSEMBLY
IP-13
C
D
E
F
G
H
J
K
L
M
A
B
IP
(G) Cluster Lid Finisher Lower
Disconnect pawls and clips, and remove cluster lid finisher lower.
(H) Instrument Finisher B
Disconnect clips, and remove instrument finisher B.
(I) Cluster Lid C Assembly
1.
Remove screws.
2.
Disconnect harness connector of display unit and audio unit,
and remove cluster lid C assembly.
(J) Instrument Driver Lower Panel
1.
Remove screws.
2.
Pull back to your side, disconnect metal clips and remove instru-
ment driver lower panel.
3.
Disconnect in-vehicle sensor and each electrical parts connec-
tors.
4.
Remove grommet, and remove hood lock cable.
(K) Steering Column Covers
1.
Remove screws and pawls and remove steering column cover front lower.
2.
Disconnect pawls, and remove upper and lower side of steering column covers.
(L) Lighting and Turn Signal Switch
Remove lighting and turn signal switch. Refer to
LT-91, "LIGHTING AND TURN SIGNAL SWITCH"
PIIB2705E
PIIB2706E
PIIB2707E
PIIB2708E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст