Infiniti G35 (V35). Manual — part 545
POWER WINDOW SYSTEM
GW-51
C
D
E
F
G
H
J
K
L
M
A
B
GW
3.
CHECK DOOR KEY CYLINDER SWITCH GROUND
Check continuity between door key cylinder switch connector D15
terminal 5 and ground.
OK or NG
OK
>> GO TO 4.
NG
>> Repair or replace harness.
4.
CHECK DOOR KEY CYLINDER SWITCH
Check continuity between door key cylinder switch terminal 1, 6 and 5.
OK or NG
OK
>> Further inspection is necessary. Refer to symptom
chart.
NG
>> Replace door key cylinder switch.
5 (B) – Ground
: Continuity should exist.
PIIA3602E
Terminals
Key position
Continuity
1
5
Neutral / Unlock
No
Lock
Yes
6
Neutral / Lock
No
Unlock
Yes
PIIA3603E
GW-52
FRONT DOOR GLASS AND REGULATOR
FRONT DOOR GLASS AND REGULATOR
PFP:80300
Removal and Installation
NIS000EV
DOOR GLASS
Removal
1.
Remove the door finisher. Refer to
2.
Operate the power window main switch to raise/lower the door
window until the glass mounting bolts can be seen.
3.
Remove the glass mounting bolts.
PIIA3455E
1.
Door glass
2.
Regulator assembly
3.
Power window motor
4.
Module assembly
5.
Glass stabilizer
PIIA3456E
FRONT DOOR GLASS AND REGULATOR
GW-53
C
D
E
F
G
H
J
K
L
M
A
B
GW
4.
While holding the door glass, raise it at the rear end to pull
toward the outside of the door.
Installation
Install in the reverse order of removal.
REGULATOR ASSEMBLY
Removal
1.
Remove the door glass. Refer to
2.
Remove the mounting bolts, and remove the module assembly.
3.
Disconnect the harness connector for the module assembly, and
unclip the harness from the back.
Installation
Install in the reverse order of removal.
Inspection after Removal
Check the regulator assembly for the following items. If a malfunc-
tion is detected, replace or grease it.
●
Wire wear
●
Regulator deformation
●
Grease condition for each sliding part
The arrows in the figure show the application points of the body
grease.
PIIA3461E
SIIA0287E
PIIA3457E
GW-54
FRONT DOOR GLASS AND REGULATOR
Disassembly and Assembly
NIS000EW
REGULATOR ASSEMBLY
Disassembly
Remove power window motor and guide rail from module assem-
bly.
Assembly
Assemble in the reverse order of removal.
Inspection after Installation
NIS000EX
SETTING OF LIMIT SWITCH
If any of the following work has been done, set the limit switch (integrated in the motor).
●
Removal and installation of the regulator.
●
Removal and installation of the motor from the regulator.
●
Operate the regulators as a unit.
●
Removal and installation of the glass.
Resetting
After installing each component to the vehicle, follow the steps below.
1.
With the door open, lift up and hold the power window switch until the door glass is fully closed.
2.
Get inside the vehicle and close the door.
You need to close the door so the door switch is fully depressed.
3.
Press and hold the reset switch. While holding the reset switch, press down and hold the power window
switch until the door glass is fully opened.
4.
Release the reset switch.Then, lift up and hold the power win-
dow switch until the door glass is fully closed.
5.
Open the door to release the door switch. The door glass should
partially move down.
CAUTION:
●
Do not use the window auto function.
●
Do not release the switch before the window is fully
stopped.
FITTING INSPECTION
●
Check that the glass is securely fit into the glass run groove.
●
Lower the glass slightly [approx. 10 to 20 mm (0.39 to 0.79 in)] and check that the clearance to the sash is
parallel. If the clearance between the glass and sash is not parallel, loosen the regulator mounting bolts,
guide rail mounting bolts, and glass and guide rail mounting bolts to correct the glass position.
–
Regulator mounting bolt and nut
–
Glass and guide rail mounting bolt
PIIA3458E
SIIA0347E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст