Infiniti G35 (V35). Manual — part 47
TROUBLE DIAGNOSIS FOR SYMPTOMS
AT-179
D
E
F
G
H
I
J
K
L
M
A
B
AT
TROUBLE DIAGNOSIS FOR SYMPTOMS
PFP:00007
Wiring Diagram — AT — NONDTC
NCS000HX
TCWM0411E
AT-180
TROUBLE DIAGNOSIS FOR SYMPTOMS
TCWM0412E
TROUBLE DIAGNOSIS FOR SYMPTOMS
AT-181
D
E
F
G
H
I
J
K
L
M
A
B
AT
TCM terminals and data are reference value. Measured between each terminal and ground.
A/T CHECK Indicator Lamp Does Not Come On
NCS000HY
SYMPTOM:
A/T CHECK indicator lamp does not come on for about 2 seconds when turning ignition switch to ON.
DIAGNOSTIC PROCEDURE
1.
CHECK CAN COMMUNICATION LINE
Perform self-diagnosis. Refer to
AT-86, "SELF-DIAGNOSTIC RESULT MODE"
Is a malfunction in the CAN communication indicated in the results?
YES
>> Check CAN communication line. Refer to
AT-98, "DTC U1000 CAN COMMUNICATION LINE"
.
NO
>> GO TO 2.
2.
CHECK A/T CHECK INDICATOR LAMP CIRCUIT
Check combination meter. Refer to
OK or NG
OK
>> GO TO 3.
NG
>> Repair or replace damaged parts.
3.
CHECK TCM POWER SUPPLY AND GROUND CIRCUIT
Check TCM power supply and ground circuit. Refer to
AT-172, "MAIN POWER SUPPLY AND GROUND CIR-
OK or NG
OK
>> INSPECTION END
NG
>> Repair or replace damaged parts.
Engine Cannot Be Started in “P” or “N” Position
NCS000HZ
SYMPTOM:
●
Engine cannot be started with selector lever in “P” or “N” position.
●
Engine can be started with selector lever in “D” or “R” position.
DIAGNOSTIC PROCEDURE
1.
CHECK PNP SWITCH CIRCUIT
Perform self-diagnosis. Refer to
AT-86, "SELF-DIAGNOSTIC RESULT MODE"
Do the self-diagnosis results indicate PNP switch?
YES
>> Check the malfunctioning system. Refer to
AT-106, "DTC P0705 PARK/NEUTRAL POSITION
NO
>> GO TO 2.
Terminal
Wire
color
Item
Condition
Data (Approx.)
3
L
CAN-H
–
–
4
PU
K-line (CONSULT-
II signal)
The terminal is connected to the data link connector for CONSULT-II.
–
7
R
Back-up lamp
relay
Selector lever in “R” position.
0 V
Selector lever in other positions.
Battery voltage
8
P
CAN-L
–
–
AT-182
TROUBLE DIAGNOSIS FOR SYMPTOMS
2.
CHECK A/T POSITION
AT-216, "Checking of A/T Position"
.
OK or NG
OK
>> GO TO 3.
NG
>> Adjust A/T position. Refer to
AT-215, "Adjustment of A/T Position"
3.
CHECK STARTING SYSTEM
Check starting system. Refer to
OK or NG
OK
>> INSPECTION END
NG
>> Repair or replace damaged parts.
In “P” Position, Vehicle Moves When Pushed
NCS000I0
SYMPTOM:
Even though the selector lever is set in the “P” position, the parking mechanism is not actuated,
allowing the vehicle to be moved when it is pushed.
DIAGNOSTIC PROCEDURE
1.
CHECK A/T POSITION
AT-216, "Checking of A/T Position"
.
OK or NG
OK
>> GO TO 2.
NG
>> Adjust A/T position. Refer to
AT-215, "Adjustment of A/T Position"
2.
CHECK PARKING COMPONENTS
Check parking components. Refer to
.
OK or NG
OK
>> INSPECTION END
NG
>> Repair or replace damaged parts.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст