Infiniti G35 (V35). Manual — part 677
PS-18
STEERING COLUMN
DISASSEMBLY
Remove parts from jacket tube assembly. Refer to
PS-17, "COMPONENTS (ELECTRICITY TYPE)"
INSPECTION AFTER DISASSEMBLY
Check tilt and telescopic mechanism components for malfunction. Replace if there are.
ASSEMBLY
Assemble is the reverse order of the disassembly. For tightening torque, refer to
INSPECTION AFTER ASSEMBLY
Check tilt and telescopic mechanism operating range.
7.
Tilt unit assembly
8.
Connector assembly
9.
Clamp
10. Spring
11.
Telescopic unit assembly
12. Telescopic sensor assembly
Operating range L
1
30 mm (1.18 in)
Operating range L
2
30 mm (1.18 in)
Operating range L
3
20 mm (0.79 in)
SGIA1248E
POWER STEERING GEAR AND LINKAGE
PS-19
C
D
E
F
H
I
J
K
L
M
A
B
PS
POWER STEERING GEAR AND LINKAGE
PFP:49001
Removal and Installation
NGS00015
COMPONENTS (WITHOUT EPS)
COMPONENTS (WITH EPS)
CAUTION:
Spiral cable may snap due to steering operation if steering column is separated from steering gear
assembly. Therefore fix steering wheel with a string to avoid turns.
REMOVAL
1.
Set wheels in the straight-ahead position.
2.
Remove undercover and tires from vehicle with power tool.
3.
Remove front crossbar. Refer to
1. Cotter pin
2.
Steering gear assembly
3.
Rack mounting bracket
4. Rack mounting insulator
SGIA0821E
1.
Cotter pin
2.
Steering gear assembly
3.
Rack mounting insulator
4.
Rack mounting bracket
Refer to
, for the symbols in the figure.
SGIA1471E
PS-20
POWER STEERING GEAR AND LINKAGE
4.
Remove cotter pin at steering outer socket, then loosen mounting nut.
5.
Use a ball joint remover (SST) to remove steering outer socket
from steering knuckle. Be careful not to damage ball joint boot.
CAUTION:
Tighten temporarily mounting nut to prevent damage to
threads and to prevent ball joint remover (SST) from com-
ing off.
6.
Remove oil pipings (high pressure side and low pressure side)
from steering gear assembly, then drain fluid from pipings.
7.
Remove power steering solenoid valve harness connector (with
EPS). Refer to
8.
Loosen bolt on upper yoke of lower joint and remove bolt on
lower yoke of joint, then slide lower joint into lower shaft. Sepa-
rate steering gear assembly from lower shaft.
9.
Tack bolt on upper yoke of lower joint, fix lower joint to lower
shaft.
10. Remove the fixing bolt and remove steering gear assembly, rack
mounting bracket and insulator from vehicle.
SGIA0341E
SGIA0367E
SGIA0348E
POWER STEERING GEAR AND LINKAGE
PS-21
C
D
E
F
H
I
J
K
L
M
A
B
PS
INSTALLATION
●
Refer to
PS-19, "Removal and Installation"
for tightening torque. Install in the reverse order of removal.
●
After removing/installing or replacing steering components, check wheel alignment. Refer to
●
Install steering gear to vehicle, refer to the tightening order
shown in the figure.
●
When steering wheel is set in the straight ahead direction, con-
firm slit of lower joint fits with the projection on rear cover cap,
furthermore marking position on steering gear assembly nearly
fits with the projection on rear cover cap.
●
After installation, bleed air from piping. Refer to
SGIA0369E
SGIA0147E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст