Infiniti G35 (V35). Manual — part 495
ENGINE ASSEMBLY
EM-135
C
D
E
F
G
H
I
J
K
L
M
A
EM
●
For a location with a positioning pin, insert it securely into hole of
mating part.
●
For a part with a specified installation orientation, refer to com-
ponent figure in
●
When installing engine mounting brackets (RH and LH) on cylin-
der block, tighten two upper bolts (shown as “A” in the figure)
first. Then tighten two lower bolts (shown as “B” in the figure).
●
Tighten rear engine mounting member bolts in numerical order
as shown in the figure.
INSPECTION AFTER INSTALLATION
Inspection for Leaks
The following are procedures for checking fluids leak, lubricates leak and exhaust gases leak.
●
Before starting engine, check oil/fluid levels including engine coolant and engine oil. If less than required
quantity, fill to the specified level. Refer to
MA-10, "RECOMMENDED FLUIDS AND LUBRICANTS"
●
Use procedure below to check for fuel leakage.
–
Turn ignition switch “ON” (with engine stopped). With fuel pressure applied to fuel piping, check for fuel
leakage at connection points.
–
Start engine. With engine speed increased, check again for fuel leakage at connection points.
●
Run engine to check for unusual noise and vibration.
●
Warm up engine thoroughly to make sure there is no leakage of fuel, exhaust gases, or any oil/fluids
including engine oil and engine coolant.
●
Bleed air from lines and hoses of applicable lines, such as in cooling system.
●
After cooling down engine, again check oil/fluid levels including engine oil and engine coolant. Refill to the
specified level, if necessary.
PBIC2062E
PBIC1684E
PBIC1683E
EM-136
ENGINE ASSEMBLY
Summary of the inspection items:
* Transmission/transaxle/CVT fluid. power steering fluid, brake fluid, etc.
Items
Before starting engine
Engine running
After engine stopped
Engine coolant
Level
Leakage
Level
Engine oil
Level
Leakage
Level
Other oils and fluid*
Level
Leakage
Level
Fuel
Leakage
Leakage
Leakage
Exhaust gases
—
Leakage
—
CYLINDER BLOCK
EM-137
C
D
E
F
G
H
I
J
K
L
M
A
EM
CYLINDER BLOCK
PFP:11010
Components
NBS002V5
PBIC3496E
EM-138
CYLINDER BLOCK
Disassembly and Assembly
NBS002V6
DISASSEMBLY
1.
Remove engine assembly from vehicle, and separate suspension member and transmission from engine.
Refer to
.
2.
Remove engine mounting brackets. Refer to
3.
Remove exhaust manifold (right bank). Refer to
EM-25, "EXHAUST MANIFOLD AND THREE WAY CAT-
1.
Reinforcement plate
2.
Drive plate (A/T models)
3.
Cover
4.
Gasket
5.
Knock sensor
6.
Cylinder block
7.
Rear oil seal retainer
8.
Oil jet
9.
Thrust bearing
10. Pilot converter (A/T models)
11. Pilot bushing (M/T models)
12. Main bearing
13. Crankshaft
14. Crankshaft key
15. Main bearing cap
16. Main bearing cap bolt
17. Main bearing beam
18. Baffle plate
19. Connecting rod bolt (A/T models)
20. Connecting rod bolt (M/T models)
21. Connecting rod bearing cap
22. Connecting rod bearing
23. Connecting rod
24. Snap ring
25. Piston pin
26. Piston
27. Oil ring
28. Second ring
29. Top ring
30. Flywheel (M/T models)
1.
Cylinder block
2.
Gasket
3.
Water connector
4.
Gasket
5.
Cylinder block heater
6.
Connector protector cap
PBIC2614E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст