Infiniti G35 (V35). Manual — part 797
WT-34
TROUBLE DIAGNOSIS FOR SYMPTOMS
Warning Lamp Blinks When Ignition Switch Is Turned On
NES000C6
NOTE:
If warning lamp blinks below, the system is normal.
Blink Mode A
●
This mode shows transmitter status is OFF-mode.
Perform transmitter wake up operation. Refer to
DIAGNOSTIC PROCEDURE
1.
CHECK CONNECTOR
1.
Turn ignition switch OFF.
2.
Disconnect BCM harness connector M1.
3.
Check terminals for damage or loose connections.
OK or NG
OK
>> GO TO 2.
NG
>> Repair or replace damaged parts.
2.
CHECK TIRE PRESSURE WARNING CHECK SWITCH CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect BCM harness connector.
3.
Check continuity between BCM harness connector M1 terminal
15 and ground.
OK or NG
OK
>> Replace BCM. Refer to
BCS-16, "Removal and Installa-
NG
>> Repair or replace harness connector.
SEIA0347E
Continuity should exist.
SEIA0438E
TROUBLE DIAGNOSIS FOR SYMPTOMS
WT-35
C
D
F
G
H
I
J
K
L
M
A
B
WT
Turn Signal Lamp Blinks When Ignition Switch Is Turned On
NES000C7
DIAGNOSTIC PROCEDURE
1.
CHECK TIRE PRESSURE WARNING CHECK SWITCH CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect BCM harness connector.
3.
Check continuity between BCM harness connector M1 terminal
15 and ground.
OK or NG
OK
>> Check turn signal lamp operation. Refer to
"TURN SIGNAL AND HAZARD WARNING LAMPS"
NG
>> Repair or replace harness connector.
ID Registration Can Not Be Completed
NES000C8
DIAGNOSTIC PROCEDURE
1.
ID REGISTRATION (ALL)
●
Perform ID registration of all transmitters.
Can ID registration of all transmitters be completed?
YES
>> INSPECTION END
NO
WT-29, "TROUBLE DIAGNOSIS FOR SELF-DIAGNOSTIC ITEMS"
.
Continuity should exist.
SEIA0438E
WT-36
TRANSMITTER
TRANSMITTER
PFP:40700
Removal and Installation
NES0003O
REMOVAL
1.
Deflate tire. Unscrew transmitter retaining nut and allow transmitter to fall into tire.
2.
Gently bounce tire so that transmitter falls to bottom of tire.
Place on tire changing machine and break both tire beads
ensuring that the transmitter remains at the bottom of the tire.
3.
Turn tire so that valve hole is at bottom and bounce so that
transmitter is near valve hole. Carefully lift tire onto turntable and
position valve hole (and transmitter) 270 degree from mounting/
dismounting head.
4.
Lubricate tire well and remove first side of the tire. Reach inside
the tire and remove the transmitter.
INSTALLATION
1.
Put first side of tire onto rim.
2.
Mount transmitter on rim and tighten nut.
CAUTION:
Speed for tightening nut should be less than 40 rpm.
SEIA0047E
SEIA0048E
SEIA0049E
SEIA0521E
TRANSMITTER
WT-37
C
D
F
G
H
I
J
K
L
M
A
B
WT
3.
Place wheel on turntable of tire machine. Ensure that transmitter
is 270 degree from mounting head when second side of tire is
fitted.
NOTE:
Do not touch transmitter at mounting head.
4.
Lubricate tire well and fit second side of tire as normal. Ensure that tire does not rotate relative to rim.
5.
Inflate tire and fit to appropriate wheel position.
SEIA0048E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст