Infiniti G35 (V35). Manual — part 536
SIDE WINDOW GLASS
GW-15
C
D
E
F
G
H
J
K
L
M
A
B
GW
SIDE WINDOW GLASS
PFP:83300
Removal and Installation
NIS000E6
REMOVAL
1.
Remove rear side finisher. Refer to
2.
Remove rear pillar garnish. Refer to
3.
Remove glass using piano wire or power cutting tool and an inflatable pump bag.
WARNING:
When cutting the glass from the vehicle, always wear safety glasses and heavy gloves to help prevent
glass splinters from entering your eyes or cutting your hands.
CAUTION:
●
Be careful not to scratch the glass when removing.
●
Do not set or stand the glass on its edge. Small chips may develop into cracks.
PIIB0099E
1.
Side window glass molding (upper)
2.
Side window glass
3.
Clip
4.
Side window glass molding (lower)
5.
Bond
6.
Rear fender
7.
Weatherstrip
GW-16
SIDE WINDOW GLASS
INSTALLATION
●
Use a genuine Nissan Urethane Adhesive Kit (if available) or equivalent and follow the instructions fur-
nished with it.
●
While the urethane adhesive is curing, open a door window. This will prevent the glass from being forced
out by passenger compartment air pressure when a door is closed.
●
Inform the customer that the vehicle should remain stationary until the urethane adhesive has completely
cured (preferably 24 hours). Curing time varies with temperature and humidity.
WARNING:
●
Keep heat and open flames away as primers and adhesive are flammable.
●
The materials contained in the kit are harmful if swallowed, and may irritate skin and eyes. Avoid
contact with the skin and eyes.
●
Use in an open, well ventilated location. Avoid breathing the vapors. They can be harmful if
inhaled. If affected by vapor inhalation, immediately move to an area with fresh air.
●
Driving the vehicle before the urethane adhesive has completely cured may affect the perfor-
mance of the side window in case of an accident.
CAUTION:
●
Do not use an adhesive which is past its usable term. Shelf life of this product is limited to six
months after the date of manufacture. Carefully adhere to the expiration or manufacture date
printed on the box.
●
Keep primers and adhesive in a cool, dry place. Ideally, they should be stored in a refrigerator.
●
Do not leave primers or adhesive cartridge unattended with their caps open or off.
●
The vehicle should not be driven for at least 24 hours or until the urethane adhesive has com-
pletely cured. Curing time varies depending on temperature and humidity. The curing time will
increase under lower temperature and lower humidity.
Repairing Water Leaks
Leaks can be repaired without removing and reinstalling glass.
If water is leaking between the urethane adhesive material and body or glass, determine the extent of leakage.
This can be done by applying water to the side window area while pushing glass outward.
To stop the leak, apply primer (if necessary) and then urethane adhesive to the leak point.
POWER WINDOW SYSTEM
GW-17
C
D
E
F
G
H
J
K
L
M
A
B
GW
POWER WINDOW SYSTEM
PFP:25401
Component Parts and Harness Connector Location
NIS000E7
PIIA9479E
GW-18
POWER WINDOW SYSTEM
System Description
NIS000E8
Power is supplied at all time
●
through 50A fusible link (letter F , located in the fuse and fusible link box)
●
to BCM terminal 55
●
through 10A fuse [No. 18, located in the fuse block (J/B)]
●
to BCM terminal 42
●
through BCM terminal 54
●
to power window main switch terminal 1
●
to power window sub-switch terminal 10.
With ignition switch in ON or START position, power is supplied
●
through 10A fuse [No. 1, located in the fuse block (J/B)]
●
to BCM terminal 38
●
through BCM terminal 53
●
to power window main switch terminal 10
Ground supplied
●
to BCM terminal 52
●
through body grounds M30 and M66.
●
to power window main switch terminal 15
●
through body grounds M30 and M66.
●
to power window sub-switch terminal 11
●
through body grounds M30 and M66.
MANUAL OPERATION
Driver Side Door
WINDOW UP
When the driver side window switch in the power window main switch is pressed in the up position,
Power is supplied
●
through power window main switch terminal 8.
●
to driver side power window motor terminal 2
Ground is supplied
●
to driver side power window motor terminal 1
●
through power window main switch terminal 11.
Then, the motor raises the window until the switch is released.
WINDOW DOWN
When the driver side window switch in the power window main switch is pressed in the down position
Power is supplied
●
through power window main switch terminal 11.
●
to driver side power window motor terminal 1
Ground is supplied
●
to driver side power window motor terminal 2
●
through power window main switch terminal 8.
Then, the motor lowers the window until the switch is released.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст