Infiniti G35 (V35). Manual — part 651
PB-10
PARKING BRAKE SHOE
INSTALLATION
Install all parts in the reverse order of while taking care of the following.
●
Apply brake grease to the contact areas shown in the figure.
●
The orientation of adjuster is different from left to right. Assem-
ble adjuster so that the threaded part is expanded when rotating
it to the direction shown by the arrow. Shorten adjuster to
assemble. When disassembling adjuster, apply brake grease to
the thread.
●
Adjust parking brake pedal or lever stroke to the specified
amount.
●
After replacing shoe or disc rotor, or if brake does not function
well, perform the break-in operation as follows.
BREAKING IN DRUM AND LINING
CAUTION:
Do not perform the break-in procedure excessively, because it may cause the uneven wear or prema-
ture wear of lining.
When a new disc rotor and/or parking brake shoe is installed, or when braking performance is poor, perform
the following break-in procedure.
1.
Drive the unloaded vehicle on a safe, level and dry road.
2.
Perform parking brake break-in (drag run) operation by driving the vehicle under the following conditions:
CAUTION:
To prevent lining from getting too hot, allow a cool off period of approximately 5 minutes after
every break-in operation.
3.
After the break-in procedure, check parking brake pedal or lever stroke of parking brake. If it is out of the
specification, adjust again.
SBR047C
SFIA0153E
Drive forward
●
Vehicle speed:
Approx. 30 km/h (19 MPH) set (forward)
●
Parking brake operating force:
Approx. 294 N (30 kg, 66 lb) set
●
Repeat steps three times:
Approx. 35sec.
SERVICE DATA AND SPECIFICATIONS (SDS)
PB-11
C
D
E
G
H
I
J
K
L
M
A
B
PB
SERVICE DATA AND SPECIFICATIONS (SDS)
PFP:00030
Parking Drum Brake
NFS0006E
Parking Brake Control
NFS0006F
Brake lining
Standard thickness
3.2 mm (0.126 in)
Repair limit thickness
1.5 mm (0.059 in)
Drum (disc)
Standard inner diameter
172 mm (6.77 in) dia.
Maximum inner diameter
173 mm (6.81 in) dia.
Control type
Pedal type / Lever type
Number of notches [under a force of 200 N (20 kg,45 lb)]
Pedal type
2 – 3 notches
Number of notches [under a force of 196 N (20 kg,44 lb)]
Lever type
6 – 7 notches
Number of notches when warning lamp comes on
1 notch
PB-12
SERVICE DATA AND SPECIFICATIONS (SDS)
PG-1
POWER SUPPLY, GROUND & CIRCUIT ELEMENTS
K ELECTRICAL
CONTENTS
C
D
E
F
G
H
I
J
L
M
SECTION
A
B
PG
POWER SUPPLY, GROUND & CIRCUIT ELEMENTS
POWER SUPPLY ROUTING CIRCUIT . . . . . .. 3
Schematic . . . . . . . . . . . . . . . . 3
Wiring Diagram — POWER — . . . . . . . . . 4
IPDM E/R (INTELLIGENT POWER DISTRIBUTION
MODULE ENGINE ROOM) . . . . . . . . . .. 16
System Description . . . . . . . . . . . . 16
Auto Active Test . . . . . . . . . . . . . . 21
REMOVAL . . . . . . . . . . . . . . ... 27
INSTALLATION . . . . . . . . . . . . ... 27
GROUND . . . . . . . . . . . . . . . . ... 28
Ground Distribution . . . . . . . . . . . . . 28
HARNESS . . . . . . . . . . . . . . . . . 40
Harness Layout . . . . . . . . . . . . . .. 40
Wiring Diagram Codes (Cell Codes) . . . . . .. 58
ELECTRICAL UNITS LOCATION . . . . . . . 61
Electrical Units Location . . . . . . . . . . . 61
HARNESS CONNECTOR . . . . . . . . . . . 65
Description . . . . . . . . . . . . . . . .. 65
ELECTRICAL UNITS . . . . . . . . . . . . 68
Terminal Arrangement . . . . . . . . . . . 68
SMJ (SUPER MULTIPLE JUNCTION) . . . . . . 69
Terminal Arrangement . . . . . . . . . . . 69
STANDARDIZED RELAY . . . . . . . . . . .. 71
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст