Infiniti G35 (V35). Manual — part 552
REAR WINDOW DEFOGGER
GW-79
C
D
E
F
G
H
J
K
L
M
A
B
GW
Filament Repair
NIS000FJ
REPAIR EQUIPMENT
●
Conductive silver composition (Dupont No. 4817 or equivalent)
●
Ruler 30 cm (11.8 in) long
●
Drawing pen
●
Heat gun
●
Alcohol
●
Cloth
REPAIRING PROCEDURE
1.
Wipe broken heat wire and its surrounding area clean with a
cloth dampened in alcohol.
2.
Apply a small amount of conductive silver composition to tip of
drawing pen.
Shake silver composition container before use.
3.
Place ruler on glass along broken line. Deposit conductive silver
composition on break with drawing pen. Slightly overlap existing
heat wire on both sides [preferably 5 mm (0.20 in)] of the break.
4.
After repair has been completed, check repaired wire for conti-
nuity. This check should be conducted 10 minutes after silver
composition is deposited.
Do not touch repaired area while test is being conducted.
5.
Apply a constant stream of hot air directly to the repaired area
for approximately 20 minutes with a heat gun. A minimum dis-
tance of 3 cm (1.2 in) should be kept between repaired area and
hot air outlet.
If a heat gun is not available, let the repaired area dry for 24
hours.
PIIA0215E
SEL012D
SEL013D
GW-80
DOOR MIRROR
DOOR MIRROR
PFP:96301
Wring Diagram –MIRROR–
NIS000FK
TIWM0478E
DOOR MIRROR
GW-81
C
D
E
F
G
H
J
K
L
M
A
B
GW
Removal and Installation
NIS000FL
CAUTION:
Be careful not to damage the mirror bodies.
REMOVAL
1.
Remove the door finisher. Refer to
.
2.
Remove the front door sash cover.
3.
Disconnect the door mirror harness connector.
4.
Remove the door mirror mounting nuts, and remove the door mirror assembly.
INSTALLATION
Install in the reverse order of removal.
PIIB0100E
1.
Door mirror assembly
2.
Front door sash cover
GW-82
DOOR MIRROR
Disassembly and Assembly
NIS000FM
DISASSEMBLY
1.
Place the mirror body with mirror glass facing upward.
2.
Put a strip of protective tape on mirror body.
3.
As shown in the figure insert a small slotted screwdriver into the
recess between mirror base (mirror holder) and mirror holder
bracket and push up pawls to remove mirror holder lower half
side.
NOTE:
When pushing up pawls, do not attempt to use 1 recess only, be sure
to push up with both recesses.
Insert screwdriver into recesses, and push up while rotating (twist) to
make work easier.
4.
Remove terminals of mirror heater attachment.
5.
Lightly lift up lower side of mirror surface, and detach pawls of upper side as if pulling it out. Remove mir-
ror surface from mirror body.
NOTE:
Be certain not to allow grease on sealing agent in center of mirror body assembly (actuator) or back side of
mirror surface (mirror holder).
ASSEMBLY
1.
Place mirror holder bracket and mirror body assembly (actuator) in a horizontal position.
2.
Connect terminals of heater installed mirror.
3.
Fit the upper pawls on the mirror face onto the mirror holder
bracket first, then press the lower side of mirror face until a click
sound is heard to engage the lower pawls.
NOTE:
After installation, visually check that lower pawls are securely
engaged from the bottom of mirror face.
PIIA2159E
PIIA2160E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст