Infiniti G35 (V35). Manual — part 463
PREPARATION
EM-7
C
D
E
F
G
H
I
J
K
L
M
A
EM
PREPARATION
PFP:00002
Special Service Tools (SST)
NBS000JK
The actual shapes of Kent-Moore tools may differ from those of special service tools illustrated here.
Tool number
(Kent-Moore No.)
Tool name
Description
ST0501S000
(
—
)
Engine stand assembly
1. ST05011000
(
—
)
Engine stand
2. ST05012000
(
—
)
Base
Disassembling and assembling
KV10106500
(
—
)
Engine stand shaft
KV10117000
(J41262)
Engine sub-attachment
KV10117000 has been replaced with
KV10117001 (KV10117000 is no longer in
production, but it is usable.)
KV10117001
(
—
)
Engine sub-attachment
Installing on the cylinder block
KV10116200
(J26336-A)
Valve spring compressor
1. KV10115900
(J26336-20)
Attachment
2. KV10109220
(
—
)
Adaptor
Disassembling valve mechanism
Part (1) is a component of KV10116200
(J26336-A), but part (2) is not so.
KV10107902
(J38959)
Valve oil seal puller
Replacing valve oil seal
NT042
NT028
NT373
NT372
PBIC1650E
NT011
EM-8
PREPARATION
KV10115600
(J-38958)
Valve oil seal drift
Installing valve oil seal
Use side A.
a: 20 (0.79) dia. d: 8 (0.31) dia.
b: 13 (0.51) dia. e: 10.7 (0.421)
c: 10.3 (0.406) dia. f: 5 (0.20)
Unit: mm (in)
EM03470000
(J8037)
Piston ring compressor
Installing piston assembly into cylinder bore
ST16610001
(J23907)
Pilot bushing puller
Removing crankshaft pilot bushing
KV10111100
(J37228)
Seal cutter
Removing oil pan (lower and upper), front
and rear timing chain case, etc.
WS39930000
(
—
)
Tube presser
Pressing the tube of liquid gasket
KV10112100
(BT8653-A)
Angle wrench
Tightening bolts for bearing cap, cylinder
head, etc. in angle
KV10117100
(J3647-A)
Heated oxygen sensor wrench
Loosening or tightening heated oxygen
sensor
For 22 mm (0.87 in) width hexagon nut
Tool number
(Kent-Moore No.)
Tool name
Description
S-NT603
NT044
NT045
NT046
NT052
NT014
NT379
PREPARATION
EM-9
C
D
E
F
G
H
I
J
K
L
M
A
EM
Commercial Service Tools
NBS000JL
KV10114400
(J38365)
Heated oxygen sensor wrench
Loosening or tightening air fuel ratio sensor
a: 22 mm (0.87 in)
KV10117700
(J44716)
Ring gear stopper
Removing and installing crankshaft pulley
—
(J-45488)
Quick connector release
Removing fuel tube quick connectors in
engine room
Tool number
(Kent-Moore No.)
Tool name
Description
NT636
NT822
PBIC0198E
(Kent-Moore No.)
Tool name
Description
(
—
)
Power tool
Loosening bolts and nuts
(
—
)
TORX socket
Removing and installing flywheel
Size: T55
(
—
)
Manual lift table caddy
Removing and installing engine
PBIC0190E
PBIC1113E
ZZA1210D
EM-10
PREPARATION
(BT3373-F)
Belt tension gauge
Checking drive belt tension
(J24239-01)
Cylinder head bolt wrench
Loosening and tightening cylinder head bolt,
and used with angle wrench [SST:
KV10112100 (BT8653-A)]
a: 13 (0.51) dia.
b: 12 (0.47)
c: 10 (0.39)
Unit: mm (in)
(
—
)
Spark plug wrench
Removing and installing spark plug
(
—
)
Valve seat cutter set
Finishing valve seat dimensions
(
—
)
Piston ring expander
Removing and installing piston ring
(
—
)
Valve guide drift
Removing and installing valve guide
Intake & Exhaust:
a = 9.5 mm (0.374 in) dia.
b = 5.5 mm (0.217 in) dia.
(
—
)
Valve guide reamer
Reaming valve guide with (1) or hole for
oversize valve guide with (2)
Intake & Exhaust:
d
1
= 6.0 mm (0.236 in) dia.
d
2
= 10.2 mm (0.402 in) dia.
(Kent-Moore No.)
Tool name
Description
AMA126
NT583
NT047
NT048
NT030
NT015
NT016
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст