Infiniti G20 (P11). Manual — part 114
SBR646
SBR868C
8.
Insert piston seal into groove on cylinder body.
9.
With piston boot fitted to piston, insert piston boot into groove
on cylinder body and fit piston by turning it clockwise with long
nose pilers, or suitable tool.
SBR027D
10. Fit toggle lever, return spring and cable guide.
SBR306E
11. Adjust the piston to the right angle as shown in the figure.
SBR307E
Installation
NCBR0043
CAUTION:
I
Refill with new brake fluid “DOT 3”.
I
Never reuse drained brake fluid.
1.
Install caliper assembly.
I
As shown in the figure, align the piston’s concave to the pad’s
convex, then install the cylinder body to the torque member.
2.
Install brake hose to caliper securely.
3.
Install all parts and secure all bolts.
4.
Bleed air. Refer to “Bleeding Brake System”, BR-8.
GI
MA
EM
LC
EC
FE
CL
MT
AT
AX
SU
ST
RS
BT
HA
SC
EL
IDX
REAR DISC BRAKE
Assembly (Cont’d)
BR-31
Components
NCBR0044
SBR325E
SBR897D
Removal and Installation
NCBR0045
1.
To remove parking brake cable, first remove center console.
2.
Disconnect warning switch connector.
3.
Remove bolts, slacken off and remove adjusting nut.
SBR025D
4.
Remove lock plate and disconnect cable.
PARKING BRAKE CONTROL
Components
BR-32
Inspection
NCBR0046
1.
Check control lever for wear or other damage. Replace if nec-
essary.
2.
Check wires for discontinuity or deterioration. Replace if nec-
essary.
3.
Check warning lamp and switch. Replace if necessary.
4.
Check parts at each connecting portion and, if found deformed
or damaged, replace.
SBR029D
Adjustment
NCBR0047
Pay attention to the following points after adjustment.
1)
There is no drag when control lever is being released.
2)
Be sure that toggle lever returns to stopper when parking brake
lever is released.
SBR042D
1.
Loosen parking brake cable.
2.
Depress brake pedal fully more than five times.
3.
Operate control lever 10 times or more with a full stroke [203.5
mm (8.01 in)].
4.
Adjust control lever by turning adjusting nut.
5.
Pull control lever with specified amount of force. Check lever
stroke and ensure smooth operation.
Number of notches:
6 - 7 [196 N (20 kg, 44 lb)]
6.
Bend warning lamp switch plate. Warning lamp should come
on when lever is pulled “A” notches. It should go off when the
lever is fully released.
Number of “A” notches: 1
GI
MA
EM
LC
EC
FE
CL
MT
AT
AX
SU
ST
RS
BT
HA
SC
EL
IDX
PARKING BRAKE CONTROL
Inspection
BR-33
Purpose
NCBR0082
The ABS consists of electronic and hydraulic components. It allows for control of braking force so that lock-
ing of the wheels can be avoided.
The ABS:
1) Ensures proper tracking performance through steering wheel operation.
2) Enables obstacles to be avoided through steering wheel operation.
3) Ensures vehicle stability by preventing flat spins.
ABS (Anti-Lock Brake System) Operation
NCBR0083
I
When the vehicle speed is less than 10 km/h (6 MPH) this system does not work.
I
The Anti-Lock Brake System (ABS) has self-test capabilities. The system turns on the ABS warning lamp
for 1 second after turning the ignition switch ON. The system performs another test the first time the vehicle
reaches 6 km/h (4 MPH). A mechanical noise may be heard as the ABS performs a self-test. This is a
normal part of the self-test feature. If a malfunction is found during this check, the ABS warning lamp will
come on.
I
During ABS operation, a mechanical noise may be heard. This is a normal condition.
ABS Hydraulic Circuit
NCBR0084
SBR984D
1.
Inlet solenoid valve
2.
Outlet solenoid valve
3.
Reservoir
4.
Pump
5.
Motor
6.
Inlet valve
7.
Outlet valve
8.
Bypass check valve
9.
Damper
DESCRIPTION
ABS
Purpose
BR-34
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст