Infiniti G20 (P11). Manual — part 526
Disassembly and Assembly
=NCST0019
SST698C
1.
Combination switch
2.
Snap ring
3.
Washer
4.
O-ring
5.
Jacket tube assembly
6.
Spring
7.
Steering column lower cover
8.
Column shaft assembly
SST670B
I
When disassembling and assembling, unlock steering lock
with key.
I
Remove combination switch.
I
Ensure that rounded surface of snap ring faces toward bear-
ing when snap ring is installed.
I
Install snap ring on upper shaft with a suitable tool.
SST741A
I
Steering lock
a)
Break self-shear type screws with a drill or other appropriate
tool.
GI
MA
EM
LC
EC
FE
CL
MT
AT
AX
SU
BR
RS
BT
HA
SC
EL
IDX
STEERING WHEEL AND STEERING COLUMN
Disassembly and Assembly
ST-13
SST742A
b)
Install new self-shear type screws and then cut off self-shear
type screw heads.
SST334C
Inspection
NCST0020
I
When steering wheel does not turn smoothly, check the steer-
ing column as follows and replace damaged parts.
a)
Check column bearings for damage or unevenness. Lubricate
with recommended multi-purpose grease or replace steering
column as an assembly, if necessary.
b)
Check jacket tube for deformation or breakage. Replace if
necessary.
I
When the vehicle comes into a light collision, check length “L”.
Column length “L”:
535.9 - 538.1 mm (21.10 - 21.18 in)
If out of the specifications, replace steering column as an assem-
bly.
SST582B
TILT MECHANISM
NCST0020S01
I
After installing steering column, check tilt mechanism opera-
tion.
STEERING WHEEL AND STEERING COLUMN
Disassembly and Assembly (Cont’d)
ST-14
Components
NCST0021
SST976C
1.
Rear cover cap
2.
Sub-gear assembly
3.
O-ring
4.
Shim
5.
Pinion oil seal
6.
Lock nut
7.
Adjusting screw
8.
Spring
9.
Spring disc
10. Washer
11. Spring seat
12. Retainer
13. Gear housing
14. Center bushing
15. Rack oil seal
16. Rack assembly
17. Rack seal ring
18. O-ring
19. Rack oil seal
20. End cover assembly
21. Boot clamp
22. Dust boot
23. Boot band
24. Lock plate
25. Tie-rod inner socket
26. Tie-rod outer socket
27. Cotter pin
28. Gear housing tube
29. Spacer
GI
MA
EM
LC
EC
FE
CL
MT
AT
AX
SU
BR
RS
BT
HA
SC
EL
IDX
POWER STEERING GEAR AND LINKAGE
Components
ST-15
Removal and Installation
NCST0022
SST835C
1.
Lower joint
2.
Hole cover
3.
Insulator bracket
4.
Rear cover cap
5.
Gear and linkage assembly
6.
Rack mounting insulator
7.
Gear housing mounting bracket
8.
Cotter pin
9.
Clamp
SFA455BC
CAUTION:
I
The rotation of the spiral cable (SRS “AIR BAG” compo-
nent part) is limited. If the steering gear must be removed,
set the front wheels in the straight-ahead direction. Do not
rotate the steering column while the steering gear is
removed.
I
Remove the steering wheel before removing the steering
lower joint to avoid damaging the SRS spiral cable.
I
Detach tie-rod outer sockets from knuckle arms with Tool.
I
When disconnecting steering shaft lower joint, follow the pro-
cedure shown below.
1.
Remove nuts for fitting the hole cover.
2.
Disconnect the lower joint while shifting the hole cover.
POWER STEERING GEAR AND LINKAGE
Removal and Installation
ST-16
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст