Infiniti G20 (P11). Manual — part 215
4
CHECK HEATED OXYGEN SENSOR 2 HEATER (REAR)
Refer to “Component Inspection”, EC-271.
OK or NG
OK
©
GO TO 5.
NG
©
Replace heated oxygen sensor 2 (rear).
5
CHECK INTERMITTENT INCIDENT
Perform “TROUBLE DIAGNOSIS FOR INTERMITTENT INCIDENT”, EC-146.
©
INSPECTION END
SEF221W
Component Inspection
NCEC0187
HEATED OXYGEN SENSOR 2 HEATER (REAR)
NCEC0187S01
Check the following.
1.
Check resistance between terminals 2 and 3.
Resistance: 2.3 - 4.3
Ω
at 25°C (77°F)
2.
Check continuity.
Terminal No.
Continuity
1 and 2, 3, 4
No
4 and 1, 2, 3
If NG, replace the heated oxygen sensor 2 (rear).
CAUTION:
I
Discard any heated oxygen sensor which has been
dropped from a height of more than 0.5 m (19.7 in) onto a
hard surface such as a concrete floor; use a new one.
I
Before installing new oxygen sensor, clean exhaust sys-
tem threads using Oxygen Sensor Thread Cleaner tool
J-43897-18 or J-43897-12 and approved anti-seize lubri-
cant.
GI
MA
EM
LC
FE
CL
MT
AT
AX
SU
BR
ST
RS
BT
HA
SC
EL
IDX
DTC P0141 HEATED OXYGEN SENSOR 2 HEATER (REAR)
Diagnostic Procedure (Cont’d)
EC-271
On Board Diagnosis Logic
NCEC0188
With the Air/Fuel Mixture Ratio Self-Learning Control, the actual mixture ratio can be brought closely to the
theoretical mixture ratio based on the mixture ratio feedback signal from the heated oxygen sensor 1 (front).
The ECM calculates the necessary compensation to correct the offset between the actual and the theoretical
ratios.
In case the amount of the compensation value is extremely large (The actual mixture ratio is too lean.), the
ECM judges the condition as the fuel injection system malfunction and lights up the MIL (2 trip detection logic).
Sensor
Input Signal to ECM
ECM func-
tion
Actuator
Heated oxygen sensor 1 (front)
Density of oxygen in exhaust gas
(Mixture ratio feedback signal)
Fuel injec-
tion & mix-
ture ratio
control
Injectors
DTC No.
Malfunction is detected when ...
Check Items (Possible Cause)
P0171
I
Fuel injection system does not operate properly.
I
The amount of mixture ratio compensation is too large.
(The mixture ratio is too lean.)
I
Intake air leaks
I
Heated oxygen sensor 1 (front)
I
Injectors
I
Exhaust gas leaks
I
Incorrect fuel pressure
I
Lack of fuel
I
Mass air flow sensor
I
Incorrect PCV hose connection
SEF215Z
SEF058Y
DTC Confirmation Procedure
NCEC0189
NOTE:
If “DTC Confirmation Procedure” has been previously conducted,
always turn ignition switch “OFF” and wait at least 10 seconds
before conducting the next test.
With CONSULT-II
1)
Start engine and warm it up to normal operating temperature.
2)
Turn ignition switch “OFF” and wait at least 10 seconds.
3)
Turn ignition switch “ON” and select “SELF-LEARNING CONT”
in “WORK SUPPORT” mode with CONSULT-II.
4)
Clear the self-learning control coefficient by touching “CLEAR”.
5)
Select “DATA MONITOR” mode with CONSULT-II.
6)
Start engine again and let it idle for at least 10 minutes.
The 1st trip DTC P0171 should be detected at this stage, if a
malfunction exists. If so, go to “Diagnostic Procedure”,
EC-275.
7)
If it is difficult to start engine at step 6, the fuel injection sys-
tem has a malfunction.
8)
Crank engine while depressing accelerator pedal. If engine
starts, go to “Diagnostic Procedure”, EC-275. If engine does
not start, visually check for exhaust and intake air leak.
DTC P0171 FUEL INJECTION SYSTEM FUNCTION (LEAN SIDE)
On Board Diagnosis Logic
EC-272
SEF840X
With GST
1)
Start engine and warm it up to normal operating temperature.
2)
Turn ignition switch “OFF” and wait at least 10 seconds.
3)
Disconnect mass air flow sensor harness connector. Then
restart and run engine for at least 3 seconds at idle speed.
4)
Stop engine and reconnect mass air flow sensor harness con-
nector.
5)
Select “MODE 7” with GST. Make sure 1st trip DTC P0100 is
detected.
6)
Select “MODE 4” with GST and erase the 1st trip DTC P0100.
7)
Start engine again and run it for at least 10 minutes at idle
speed.
8)
Select “MODE 7” with GST. The 1st trip DTC P0171 should be
detected at this stage, if a malfunction exists. If so, go to
“Diagnostic Procedure”, EC-275.
9)
If it is difficult to start engine at step 8, the fuel injection sys-
tem has a malfunction.
10) Crank engine while depressing accelerator pedal. If engine
starts, go to “Diagnostic Procedure”, EC-275. If engine does
not start, visually check for exhaust and intake air leak.
GI
MA
EM
LC
FE
CL
MT
AT
AX
SU
BR
ST
RS
BT
HA
SC
EL
IDX
DTC P0171 FUEL INJECTION SYSTEM FUNCTION (LEAN SIDE)
DTC Confirmation Procedure (Cont’d)
EC-273
Wiring Diagram
NCEC0190
TEC841
DTC P0171 FUEL INJECTION SYSTEM FUNCTION (LEAN SIDE)
Wiring Diagram
EC-274
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст