Infiniti G20 (P11). Manual — part 14
Judgement of Self-diagnosis Code
NCAT0022S0704
O/D OFF indicator lamp:
All judgement flickers are the same.
SAT436F
All circuits that can be confirmed by self-diagnosis are OK.
1st judgement flicker is longer than others.
SAT437F
Revolution sensor circuit is short-circuited or disconnected.
⇒
Go to VEHICLE SPEED SENSOR·A/T (REVOLUTION
SENSOR), AT-119.
2nd judgement flicker is longer than others.
SAT439F
Vehicle speed sensor circuit is short-circuited or disconnected.
⇒
Go to VEHICLE SPEED SENSOR·MTR, AT-215.
3rd judgement flicker is longer than others.
SAT441F
Throttle position sensor circuit is short-circuited or disconnected.
⇒
Go to THROTTLE POSITION SENSOR, AT-193.
4th judgement flicker is longer than others.
SAT443F
Shift solenoid valve A circuit is short-circuited or disconnected.
⇒
Go to SHIFT SOLENOID VALVE A, AT-181.
5th judgement flicker is longer than others.
SAT445F
Shift solenoid valve B circuit is short-circuited or disconnected.
⇒
Go to SHIFT SOLENOID VALVE B, AT-187.
GI
MA
EM
LC
EC
FE
CL
MT
AX
SU
BR
ST
RS
BT
HA
SC
EL
IDX
ON BOARD DIAGNOSTIC SYSTEM DESCRIPTION
CONSULT-II (Cont’d)
AT-53
O/D OFF indicator lamp:
6th judgement flicker is longer than others.
SAT447F
Overrun clutch solenoid valve circuit is short-circuited or discon-
nected.
⇒
Go to OVERRUN CLUTCH SOLENOID VALVE, AT-202.
7th judgement flicker is longer than others.
SAT449F
Torque converter clutch solenoid valve circuit is short-circuited
or disconnected.
⇒
Go to TORQUE CONVERTER CLUTCH SOLENOID
VALVE, AT-157.
8th judgement flicker is longer than others.
SAT451F
A/T fluid temperature sensor is disconnected or TCM power
source circuit is damaged.
⇒
Go to A/T FLUID TEMPERATURE SENSOR AND TCM
POWER SOURCE, AT-113.
9th judgement flicker is longer than others.
SAT453F
Engine speed signal circuit is short-circuited or disconnected.
⇒
Go to ENGINE SPEED SIGNAL, AT-124.
10th judgement flicker is longer than others.
SAT455F
Line pressure solenoid valve circuit is short-circuited or discon-
nected.
⇒
Go to LINE PRESSURE SOLENOID VALVE, AT-174.
Flickers as shown below.
SAT457F
Battery power is low.
Battery has been disconnected for a long time.
Battery is connected conversely.
(When reconnecting TCM connectors. — This is not a problem.)
ON BOARD DIAGNOSTIC SYSTEM DESCRIPTION
CONSULT-II (Cont’d)
AT-54
O/D OFF indicator lamp:
Lamp comes on.
SAT367J
PNP switch, overdrive control switch or throttle position switch
circuit is disconnected or TCM is damaged.
⇒
Go to 21. TCM Self-diagnosis Does Not Activate (PNP,
OVERDRIVE CONTROL AND THROTTLE POSITION
SWITCHES), AT-263.
t
1
= 2.5 seconds
t
2
= 2.0 seconds
t
3
= 1.0 second
t
4
= 1.0 second
GI
MA
EM
LC
EC
FE
CL
MT
AX
SU
BR
ST
RS
BT
HA
SC
EL
IDX
ON BOARD DIAGNOSTIC SYSTEM DESCRIPTION
CONSULT-II (Cont’d)
AT-55
SAT631IA
Introduction
NCAT0023
SAT632I
SEF234G
The TCM receives a signal from the vehicle speed sensor, throttle
position sensor or PNP switch and provides shift control or lock-up
control via A/T solenoid valves.
The TCM also communicates with the ECM by means of a signal
sent from sensing elements used with the OBD-related parts of the
A/T system for malfunction-diagnostic purposes. The TCM is
capable of diagnosing malfunctioning parts while the ECM can
store malfunctions in its memory.
Input and output signals must always be correct and stable in the
operation of the A/T system. The A/T system must be in good
operating condition and be free of valve seizure, solenoid valve
malfunction, etc.
It is much more difficult to diagnose a problem that occurs intermit-
tently rather than continuously. Most intermittent problems are
caused by poor electric connections or improper wiring. In this
case, careful checking of suspected circuits may help prevent the
replacement of good parts.
A visual check only, may not find the cause of the problems. A road
test with CONSULT-II (or GST) or a circuit tester connected should
be performed. Follow the “Work Flow”. Refer to AT-60.
Before undertaking actual checks, take a few minutes to talk with
a customer who approaches with a driveability complaint. The cus-
tomer can supply good information about such problems, espe-
cially intermittent ones. Find out what symptoms are present and
under what conditions they occur. A “Diagnostic Worksheet” like the
example (AT-58) should be used.
Start your diagnosis by looking for “conventional” problems first.
This will help troubleshoot driveability problems on an electronically
controlled engine vehicle.
Also check related Service bulletins for information.
TROUBLE DIAGNOSIS — INTRODUCTION
Introduction
AT-56
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст