Infiniti G20 (P11). Manual — part 226
PROCEDURE A
=NCEC0672S01
1
CHECK COOLING FAN POWER SUPPLY CIRCUIT
1. Turn ignition switch “OFF”.
2. Disconnect cooling fan relay-1.
3. Turn ignition switch “ON”.
4. Check voltage between cooling fan relay-1 terminals 1, 3, 7 and ground with CONSULT-II or tester.
SEF727W
Voltage: Battery voltage
OK or NG
OK
©
GO TO 3.
NG
©
GO TO 2.
2
DETECT MALFUNCTIONING PART
Check the following.
I
10A fuse
I
40A fusible link
I
30A fusible link
I
Harness for open or short between cooling fan relay-1 and fuse
I
Harness for open or short between cooling fan relay-1 and battery
©
Repair open circuit or short to ground or short to power in harness or connectors.
GI
MA
EM
LC
FE
CL
MT
AT
AX
SU
BR
ST
RS
BT
HA
SC
EL
IDX
DTC P0217 COOLANT OVERTEMPERATURE ENRICHMENT PROTECTION
Diagnostic Procedure (M/T Models) (Cont’d)
EC-315
3
CHECK COOLING FAN MOTOR CIRCUIT FOR OPEN AND SHORT
1. Turn ignition switch “OFF”.
2. Disconnect cooling fan motor-1 harness connector and cooling fan motor-2 harness connector.
SEF854X
3. Check harness continuity between cooling fan relay-1 terminal 5 and cooling fan motor-1 terminal 1, cooling fan
motor-1 terminal 4 and body ground. Refer to Wiring Diagram.
Continuity should exist.
4. Also check harness for short to ground and short to power.
5. Check harness continuity between cooling fan relay-1 terminal 6 and cooling fan motor-2 terminal 2, cooling fan
motor-2 terminal 1 and body ground. Refer to Wiring Diagram.
Continuity should exist.
6. Also check harness for short to ground and short to power.
OK or NG
OK
©
GO TO 4.
NG
©
Repair open circuit or short to ground or short to power in harness or connectors.
4
CHECK COOLING FAN OUTPUT SIGNAL CIRCUIT FOR OPEN AND SHORT
1. Disconnect ECM harness connector.
2. Check harness continuity between ECM terminal 13 and cooling fan relay-1 terminal 2. Refer to Wiring Diagram.
Continuity should exist.
3. Also check harness for short to ground and short to power.
OK or NG
OK
©
GO TO 6.
NG
©
GO TO 5.
5
DETECT MALFUNCTIONING PART
Check the following.
I
Harness connectors E75, M6
I
Harness connectors M49, F23
I
Harness for open or short between cooling fan relay-1 and ECM
©
Repair open circuit or short to ground or short to power in harness or connectors.
DTC P0217 COOLANT OVERTEMPERATURE ENRICHMENT PROTECTION
Diagnostic Procedure (M/T Models) (Cont’d)
EC-316
6
CHECK COOLING FAN RELAY-1
Check continuity between cooling fan relay-1 terminals 3 and 5, 6 and 7 under the following conditions.
SEF591X
OK or NG
OK
©
GO TO 7.
NG
©
Replace cooling fan relay.
7
CHECK COOLING FAN MOTOR-1
Supply battery voltage between the following terminals and check operation.
SEF937XA
OK or NG
OK
©
GO TO 8.
NG
©
Replace cooling fan motor-1.
8
CHECK COOLING FAN MOTOR-2
Supply battery voltage between the following terminals and check operation.
SEC574C
OK or NG
OK
©
GO TO 9.
NG
©
Replace cooling fan motor-2.
GI
MA
EM
LC
FE
CL
MT
AT
AX
SU
BR
ST
RS
BT
HA
SC
EL
IDX
DTC P0217 COOLANT OVERTEMPERATURE ENRICHMENT PROTECTION
Diagnostic Procedure (M/T Models) (Cont’d)
EC-317
9
CHECK INTERMITTENT INCIDENT
Perform “TROUBLE DIAGNOSIS FOR INTERMITTENT INCIDENT”, EC-146.
©
INSPECTION END
DTC P0217 COOLANT OVERTEMPERATURE ENRICHMENT PROTECTION
Diagnostic Procedure (M/T Models) (Cont’d)
EC-318
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст