Infiniti G20 (P11). Manual — part 482
Checking Disc Brake
NCMA0007S18
ROTOR
NCMA0007S1801
Check condition and thickness.
Standard thickness:
Front 22 mm (0.87 in)
Rear 9 mm (0.35 in)
Minimum thickness:
Front 20 mm (0.79 in)
Rear 8 mm (0.31 in)
SMA922A
CALIPER
NCMA0007S1802
Check for leakage.
BRA0010D
PAD
NCMA0007S1803
Check wear or damage.
Standard thickness:
Front 11 mm (0.43 in)
Rear 10 mm (0.39 in)
Minimum thickness:
Front 2 mm (0.08 in)
Rear 1.5 mm (0.059 in)
SLIA0014E
Checking Steering Gear and Linkage
NCMA0007S20
STEERING GEAR
NCMA0007S2001
I
Check gear housing and boots for looseness, damage and
grease leakage.
I
Check connection with steering column for looseness.
STEERING LINKAGE
NCMA0007S2002
Check ball joint, dust cover and other component parts for
looseness, wear, damage and grease leakage.
SST850C
Checking Power Steering Fluid and Lines
NCMA0007S21
Check fluid level in reservoir tank with engine off.
Use “HOT” range at fluid temperatures of 50 to 80°C (122 to 176°F)
or “COLD” range at fluid temperatures of 0 to 30°C (32 to 86°F).
CAUTION:
I
Do not overfill.
I
Recommended fluid is Genuine NISSAN PSF II or equiva-
lent.
Refer to “RECOMMENDED FLUIDS AND LUBRICANTS”,
MA-11.
GI
EM
LC
EC
FE
CL
MT
AT
AX
SU
BR
ST
RS
BT
HA
SC
EL
IDX
CHASSIS AND BODY MAINTENANCE
Checking Disc Brake
MA-25
SST851C
I
Check lines for improper attachment, leaks, cracks, damage,
loose connections, chafing and deterioration.
I
Check rack boots for accumulation of power steering fluid.
SMA525A
Axle and Suspension Parts
NCMA0007S24
Check front and rear axle and suspension parts for excessive play,
cracks, wear, or other damage.
I
Shake each wheel to check for excessive play.
I
Rotate each wheel to check for abnormal noise.
I
Check axle and suspension nuts and bolts for looseness.
I
Check strut (shock absorber) for oil leakage or other damage.
I
Check suspension ball joint for grease leakage and ball joint
dust cover for cracks or other damage.
SFA392B
SFA108A
Drive Shaft
NCMA0007S25
Check boot and drive shaft for cracks, wear, damage and grease
leakage.
MEL402G
Vacuum Hose
NCMA0007S26
Check vacuum hose (between ASCD actuator and ASCD pump)
for breakage, cracks or fracture.
CHASSIS AND BODY MAINTENANCE
Checking Power Steering Fluid and Lines (Cont’d)
MA-26
Lubricating Locks, Hinges and Hood Latches
NCMA0007S22
SMA913C
Checking Seat Belts, Buckles, Retractors,
Anchors and Adjusters
NCMA0007S23
SMA024DA
GI
EM
LC
EC
FE
CL
MT
AT
AX
SU
BR
ST
RS
BT
HA
SC
EL
IDX
CHASSIS AND BODY MAINTENANCE
Lubricating Locks, Hinges and Hood Latches
MA-27
Engine Maintenance
NCMA0008
DRIVE BELT DEFLECTION AND TENSION
NCMA0008S01
Deflection adjustment
Unit: mm (in)
Tension adjustment *1
Unit: N (kg, lb)
Used belt
New belt
Used belt
New belt
Limit
After adjust-
ment
Limit
After adjust-
ment
Compressor
With air condi-
tioner com-
pressor
9 (0.35)
5.5 - 6.5
(0.217 - 0.256)
4.5 - 5.5
(0.177 - 0.217)
304 (31, 68)
534 - 623
(54.5 - 63.5,
120.2 - 140.0)
652 - 740
(66.5 - 75.5,
146.6 - 166.5)
Generator
Without air
conditioner
compressor
12 - 13
(0.47 - 0.51)
8 - 9
(0.31 - 0.35)
7 - 8
(0.28 - 0.31)
265 (27, 60)
493 - 583
(50.3 - 59.5,
110.9 - 131.2)
603 - 691
(61.5 - 70.5,
135.6 - 155.5)
Power steer-
ing oil pump
With air condi-
tioner com-
pressor
12 (0.47)
8 - 9
(0.31 - 0.35)
7 - 8
(0.28 - 0.31)
265 (27, 60)
495 - 583
(50.5 - 59.5,
111.4 - 131.2)
603 - 691
(61.5 - 70.5,
135.6 - 155.5)
Without air
conditioner
compressor
12 (0.47)
8 - 9
(0.31 - 0.35)
7 - 8
(0.28 - 0.31)
265 (27, 60)
493 - 583
(50.3 - 59.5,
110.9 - 131.2)
603 - 691
(61.5 - 70.5,
135.6 - 155.5)
Applied pushing force
98 N (10 kg, 22 lb)
—
*1: If the belt tension gauge cannot be installed at check points shown, check belt tension at a different location on the belt.
SPARK PLUG TYPE
NCMA0008S02
Platinum-tipped type
Conventional type
Type
Standard
PFR5G-11
BKR5E
Hot
—
—
Cold
PFR6G-11
PFR7G-11
BKR6E, BKR7E
Plug gap
Nominal: 1.1 mm (0.043 in)
0.8 - 0.9 mm (0.031 - 0.035 in)
Chassis and Body Maintenance
NCMA0009
WHEEL BALANCE
NCMA0009S01
Maximum allowable unbalance
Dynamic (At rim flange)
g (oz)
10 (0.35) (one side)
Static
g (oz)
20 (0.71)
SERVICE DATA AND SPECIFICATIONS (SDS)
Engine Maintenance
MA-28
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст