Infiniti G35 (2008 year). Manual — part 7
The windshield wiper and washer operates
when the ignition switch is in the ON position.
Push the lever down to operate the wiper at the
following speed:
s
1
Intermittent — intermittent operation can
be adjusted by turning the knob toward
s
A
(Slower) or
s
B
(Faster). When the
speed sensing wiper interval function is
turned on, the intermittent operation
speed varies in accordance with the ve-
hicle speed. (For example, when the ve-
hicle speed is high, the intermittent op-
eration speed will be faster.) To turn this
function on and off, see “HOW TO USE
SETTING BUTTON” in the “4. Monitor,
climate, audio, phone and voice recogni-
tion systems” section.
s
2
Low — continuous low speed operation
s
3
High — continuous high speed operation
Push the lever up
s
4
to have one sweep
operation of the wiper.
Pull the lever toward you
s
5
to operate the
washer. Then the wiper will also operate several
times.
SIC3238
2-30
Instruments and controls
w
—
—
07/05/07—pattie
X
-------------------------------------------------------------------------------------------------------------------------------------------------------------
To defog/defrost the rear window glass and
outside mirrors (if so equipped), start the en-
gine and push the switch
s
1
on. The indicator
light
s
2
will come on. Push the switch again to
turn the defroster off.
It will automatically turn off in approximately 15
minutes.
CAUTION
When cleaning the inner side of the rear win-
dow, be careful not to scratch or damage the
rear window defroster.
XENON HEADLIGHTS
WARNING
HIGH VOLTAGE
● When xenon headlights are on, they produce
a high voltage. To prevent an electric shock,
never attempt to modify or disassemble. Al-
ways have your xenon headlights replaced
at an INFINITI dealer.
● Xenon headlights provide considerably
more light than conventional headlights. If
they are not correctly aimed, they might
temporarily blind an oncoming driver or the
driver ahead of you and cause a serious acci-
dent. If headlights are not aimed correctly,
immediately take your vehicle to an INFINITI
dealer and have the headlights adjusted
correctly.
When the xenon headlight is initially turned on,
its brightness or color varies slightly. However,
the color and brightness will soon stabilize.
Type A
SIC3239
Type B
SIC3278
REAR WINDOW AND OUTSIDE MIRROR
DEFROSTER SWITCH
HEADLIGHT AND TURN SIGNAL SWITCH
Instruments and controls
2-31
w
—
—
07/05/07—pattie
X
-------------------------------------------------------------------------------------------------------------------------------------------------------------
● The life of xenon headlights will be shortened
by frequent on-off operation. It is generally
desirable not to turn off the headlights for
short intervals (for example, when the ve-
hicle stops at a traffic signal). Even when the
daytime running lights are active (Canada
only), the xenon headlights do not turn on.
This way the life of the xenon headlights is
not reduced.
● If the xenon headlight bulb is close to burn-
ing out, the brightness will drastically de-
crease, the light will start blinking, or the
color of the light will become reddish. If one
or more of the above signs appear, contact an
INFINITI dealer.
HEADLIGHT SWITCH
Lighting
s
1
Turn the switch to the
position:
The front park, side marker, tail, license
plate and instrument lights will come on.
s
2
Turn the switch to the
position:
Headlights will come on and all the other
lights remain on.
Autolight system (if so equipped)
The autolight system allows the headlights to
be set so they turn on and off automatically.
To set the autolight system:
1. Make sure the headlight switch is in the
AUTO position
s
1
.
2. Push the ignition switch to the ON posi-
tion.
3. The autolight system automatically turns
the headlights on and off.
To turn the autolight system off, turn the switch
to the OFF,
, or
position.
SIC3267
SIC3268
2-32
Instruments and controls
w
—
—
07/14/07—pattie
X
-------------------------------------------------------------------------------------------------------------------------------------------------------------
The autolight system can turn on the headlights
automatically when it is dark and turn off the
headlights when it is light.
If the ignition switch is pushed to the OFF
position and one of the doors is opened and
this condition is continued, the headlights re-
main on for 5 minutes.
Automatic headlights off delay
You can keep the headlights on for up to 180
seconds after you push the ignition switch to
OFF and open any door then close all the doors.
You can adjust the period of the automatic
headlights off delay from 0 seconds (OFF) to 180
seconds. The factory default setting is 45 sec-
onds.
For automatic headlights off delay setting, see
“Auto Headlights Off Delay” in the “4. Monitor,
climate, audio, phone and voice recognition
systems” section.
Be sure not to put anything on top of the photo
sensor
s
A
located on the top of the instrument
panel. The photo sensor controls the autolight;
if it is covered, the photo sensor reacts as if it is
dark and the headlights will illuminate.
Headlight beam select
s
1
To select the low beam, put the lever in
the neutral position as shown.
s
2
To select the high beam, push the lever
forward while the switch is in the
position. Pull it back to select the low
beam.
s
3
Pulling the lever toward you will flash the
headlight high beam even when the
headlight switch is in the OFF position.
Battery saver system
A chime will sound when the driver side door is
opened with the light switch in the
or
SAA0642A
SIC3269
Instruments and controls
2-33
w
—
—
07/05/07—pattie
X
-------------------------------------------------------------------------------------------------------------------------------------------------------------
position and the ignition switch in the
ACC, OFF or LOCK position.
When the headlight switch is in the
or
position while the ignition switch is in
the ON position, the lights will automatically
turn off 5 minutes after the ignition switch has
been pushed to the OFF position.
When the headlight switch remains in the
or
position after the lights auto-
matically turn off, the lights will turn on when
the ignition switch is pushed to the ON posi-
tion.
CAUTION
● When you turn on the headlight switch again
after the lights automatically turn off, the
lights will not turn off automatically. Be sure
to turn the light switch to the OFF position
when you leave the vehicle for extended pe-
riods of time, otherwise the battery will be
discharged.
● Never leave the light switch on when the
engine is not running for extended periods of
time even if the headlights turn off
automatically.
Daytime running light system
(Canada only)
The daytime running lights automatically illumi-
nate when the engine is started with the park-
ing brake released. The daytime running lights
operate with the headlight switch in the OFF
position or in the
position. Turn the
headlight switch to the
position for full
illumination when driving at night.
If the parking brake is applied before the engine
is started, the daytime running lights do not
illuminate. The daytime running lights illumi-
nate once the parking brake is released. The
daytime running lights will remain on until the
ignition switch is pushed to the OFF position.
WARNING
When the daytime running light system is ac-
tive, tail lights on your vehicle are not on. It is
necessary at dusk to turn on your headlights.
Failure to do so could cause an accident injur-
ing yourself and others.
Adaptive Front lighting System (AFS)
(if so equipped)
The Adaptive Front lighting System (AFS) will
automatically adjust the headlights (low beam)
toward the turning direction to improve the
driver’s view. When the headlight switch is ON
and the driver operates the steering wheel in a
turn, the AFS system will be activated.
The AFS will operate:
● when the headlight switch is ON.
● when the selector lever is in any position
other than P (Park) or R (Reverse).
● when the vehicle is driven at above 16 MPH
(25 km/h) for the left-side headlight. Note
that the right-side low beam headlight will
swivel but the left side will not swivel when
the vehicle is at a stop and the steering
wheel is turned. The vehicle must attain a
speed above 16 MPH (25 km/h) before AFS
activates the left-side headlight.
2-34
Instruments and controls
w
—
—
07/14/07—pattie
X
-------------------------------------------------------------------------------------------------------------------------------------------------------------
To turn the AFS off, push the OFF side of the AFS
switch. (The AFS OFF indicator light will illumi-
nate.) Push the ON side of the switch to turn the
system on again.
AFS will also adjust the headlight to a proper
axis automatically, depending on the number of
occupants in the vehicle, the load the vehicle is
carrying and the road conditions.
If the AFS OFF indicator light blinks after the
ignition switch has been pushed to the ON
position, this may indicate that the AFS is not
functioning properly. Have the system checked
by an INFINITI dealer. When the engine is
started, the headlights will vibrate to check the
system condition. This is not a malfunction.
SIC2645
SIC3257
Instruments and controls
2-35
w
—
—
07/05/07—pattie
X
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Instrument brightness control
The instrument brightness control switch can be
operated when the ignition switch is in the ON
position. When the switch is operated, the dot
matrix liquid crystal display switches to the
brightness adjustment mode.
Push the upper switch
s
A
to brighten the
instrument panel lights. The bar
s
1
moves to
the + side. When reaching the maximum bright-
ness, “MAX” appears on the display
s
2
.
Push the lower switch
s
B
to dim the instrument
panel lights. The bar
s
1
moves to the
2 side.
When reaching the minimum brightness, “MIN”
appears on the display
s
3
. However, “MIN”
does not appear during the nighttime.
The dot matrix liquid crystal display returns to
the normal display under the following condi-
tions:
● when the instrument brightness control
switch is not operated for more than 5
seconds.
● when the side or front of the
switch or
switch on the right side of the com-
bination meter panel is pushed.
TURN SIGNAL SWITCH
s
1
Turn signal
Move the lever up or down to signal the turning
direction. When the turn is completed, the turn
signals cancel automatically.
s
2
Lane change signal
To indicate a lane change, move the lever up or
down to the point where lights begin flashing.
SIC3270
SIC3271
2-36
Instruments and controls
w
—
—
07/14/07—pattie
X
-------------------------------------------------------------------------------------------------------------------------------------------------------------
FOG LIGHT SWITCH
To turn the fog lights on, turn the headlight
switch to the
position, then turn the
switch to the
position. To turn them off,
turn the switch to the OFF position.
The headlights must be on for the fog lights to
operate.
Push the switch on to warn other drivers when
you must stop or park under emergency condi-
tions. All turn signal lights will flash.
WARNING
● If stopping for an emergency, be sure to
move the vehicle well off the road.
● Do not use the hazard warning flashers while
moving on the highway unless unusual cir-
cumstances force you to drive so slowly that
your vehicle might become a hazard to other
traffic.
● Turn signals do not work when the hazard
warning flasher lights are on.
The flasher can be actuated with the ignition
switch in any position.
Some state laws may prohibit the use of the
hazard warning flasher switch while driving.
SIC3272
SIC2574
HAZARD WARNING FLASHER SWITCH
Instruments and controls
2-37
w
—
—
07/05/07—pattie
X
-------------------------------------------------------------------------------------------------------------------------------------------------------------
To sound the horn, push the center pad area of
the steering wheel.
WARNING
Do not disassemble the horn. Doing so could
affect proper operation of the supplemental
front air bag system. Tampering with the
supplemental front air bag system may result
in serious personal injury.
CAUTION
● The battery could run down if the seat heater
is operated while the engine is not running.
● Do not use the seat heater for extended pe-
riods or when no one is using the seat.
● Do not put anything on the seat which insu-
lates heat, such as a blanket, cushion, seat
cover, etc. Otherwise, the seat may become
overheated.
● Do not place anything hard or heavy on the
seat or pierce it with a pin or similar object.
This may result in damage to the heater.
● Any liquid spilled on the heated seat should
be removed immediately with a dry cloth.
● When cleaning the seat, never use gasoline,
thinner, or any similar materials.
● If any abnormalities are found or the heated
seat does not operate, turn the switch off
and have the system checked by an INFINITI
dealer.
The front seats are warmed by built-in heaters.
The switches located on the center console can
be operated independently of each other.
1. Start the engine.
2. Select heat range.
s
1
For high heat, push the HI (High) side of
the switch.
s
2
For low heat, push the LO (Low) side of
the switch.
The indicator light in the switch
s
3
will
illuminate when low or high is selected.
SIC3312
SIC2770
HORN
HEATED SEATS (if so equipped)
2-38
Instruments and controls
w
—
—
07/05/07—pattie
X
-------------------------------------------------------------------------------------------------------------------------------------------------------------
3. To turn off the heater, return the switch to
the level position. Make sure the indicator
light goes off.
The heater is controlled by a thermostat,
automatically turning the heater on and off.
The indicator light will remain on as long as
the switch is on.
When the vehicle’s interior is warmed, or
before you leave the vehicle, be sure to turn
off the switch.
For driving or starting the vehicle on snowy
roads or slippery areas, turn on the SNOW
mode switch. The indicator light on the switch
will illuminate. When the SNOW mode is acti-
vated, engine output is controlled to avoid
wheel spin.
The vehicle should be driven with the Vehicle
Dynamic Control (VDC) system on for most
driving conditions.
If the vehicle is stuck in mud or snow, the VDC
system reduces the engine output to reduce
wheel spin. The engine speed will be reduced
even if the accelerator is depressed to the floor.
If maximum engine power is needed to free a
stuck vehicle, turn the VDC system off.
To turn off the VDC system, push the VDC OFF
switch. The
indicator will illuminate.
Push the VDC OFF switch again or restart the
engine to turn on the system. (See “VEHICLE
DYNAMIC CONTROL (VDC) SYSTEM” in the “5.
Starting and driving” section.)
SSD0351
SIC1881
SNOW MODE SWITCH (if so equipped)
VEHICLE DYNAMIC CONTROL (VDC) OFF
SWITCH
Instruments and controls
2-39
w
—
—
07/05/07—pattie
X
-------------------------------------------------------------------------------------------------------------------------------------------------------------
If the power supply is disconnected, the clock
will not indicate the correct time. Readjust the
time.
ADJUSTING THE TIME
1. To set the clock forward, push the button
s
1
.
2. To set the clock backward, push the but-
ton
s
2
.
3. To move forward or backward faster, push
and hold the button more than 5 seconds.
For details about display clock adjustment (if so
equipped), see “HOW TO USE SETTING BUTTON”
in the “4. Monitor, climate, audio, phone and
voice recognition systems” section.
The power outlet is located in the center con-
sole.
CAUTION
● The outlet and plug may be hot during or
immediately after use.
● Do not use with accessories that exceed a 12
volt, 120W (10A) power draw. Do not use
double adapters or more than one electrical
accessory.
● Use power outlet with the engine running to
avoid discharging the vehicle battery.
● Avoid using power outlet when the air condi-
tioner, headlights or rear window defroster
is on.
● This power outlet is not designed for use
with a cigarette lighter unit.
● Push the plug in as far as it will go. If good
contact is not made, the plug may overheat
or the internal temperature fuse may blow.
● Before inserting or disconnecting a plug, be
sure the electrical accessory being used is
turned OFF.
● When not in use, be sure to close the cap. Do
not allow water to contact the outlet.
SIC3325
Automatic transmission models
SIC3247
Manual transmission models
SIC3273
CLOCK
POWER OUTLET
2-40
Instruments and controls
w
—
—
07/05/07—pattie
X
-------------------------------------------------------------------------------------------------------------------------------------------------------------
FRONT
To open the ashtray lid, push the lid down and
release it
s
1
.
To empty the ashtray, pull out
s
2
.
The cigarette lighter operates when the ignition
switch is in the ON position.
Push the lighter in all the way
s
3
, then release
it. When the lighter is heated, it will spring out.
Return the lighter to its original position after
use.
CAUTION
● The cigarette lighter socket is a power
source for the cigarette lighter element only.
The use of the cigarette lighter socket as a
power source for any other accessory is not
recommended.
● Do not use any other power outlet for an
accessory lighter.
REAR
To open the ashtray lid, pull
s
1
.
To empty the ashtray, push down
s
2
, and pull
out.
SIC3219
SIC2570
CIGARETTE LIGHTER AND ASHTRAYS
Instruments and controls
2-41
w
—
—
07/05/07—pattie
X
-------------------------------------------------------------------------------------------------------------------------------------------------------------
CUP HOLDERS
CAUTION
● Avoid abrupt starting and braking when the
cup holder is being used to prevent spilling
the drink. If the liquid is hot, it can scald you
or your passenger.
● Use only soft cups in the cup holder. Hard
objects can injure you in an accident.
To open the cup holder, push the lid
s
1
.
The flap
s
A
will be folded down when inserting
a large container.
To remove the inner tray for cleaning, pull it up
as illustrated
s
2
.
To open the cup holder, slide the lid
s
1
.
Install the partition plate into the slit
s
2
.
Automatic transmission models — Front
SIC3313
Manual transmission models — Front
SIC3274
STORAGE
2-42
Instruments and controls
w
—
—
07/05/07—pattie
X
-------------------------------------------------------------------------------------------------------------------------------------------------------------
To open the console boxes, push the knob
s
A
and pull up the lid.
To close, push the lid down until the lock
latches.
To open the cup holder, pull the lid.
Manual transmission models — Console box
SIC3275
Rear
SIC1846B
Sedan
SIC3276
Coupe
SIC3462
Instruments and controls
2-43
w
—
—
07/05/07—pattie
X
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Soft bottle holder
CAUTION
● Do not use bottle holder for any other ob-
jects that could be thrown about in the ve-
hicle and possibly injure people during sud-
den braking or an accident.
● Do not use bottle holder for open liquid
containers.
SUNGLASSES HOLDER
WARNING
Keep the sunglasses holder closed while driv-
ing to prevent an accident.
To open the sunglasses holder, push
s
1
.
CAUTION
● Do not use for anything other than glasses.
● Do not leave glasses in the sunglasses
holder while parking in direct sunlight. The
heat may damage the glasses.
GLOVE BOX
WARNING
Keep glove box lid closed while driving to help
prevent injury in an accident or a sudden stop.
To open the glove box, pull the handle
s
1
.
To close, push the lid in until the lock latches.
To lock
s
2
/unlock
s
3
the glove box, use the
mechanical key. For the mechanical key usage,
see “KEYS” in the “3. Pre-driving checks and
adjustments” section.
SIC3246
SIC3469
2-44
Instruments and controls
w
—
—
07/05/07—pattie
X
-------------------------------------------------------------------------------------------------------------------------------------------------------------
CONSOLE BOX
To open the console boxes, push up the knob
s
A
and pull up the lid.
To close, push the lid down until latched.
Automatic transmission models
SIC3245
Manual transmission models
SIC3277
Instruments and controls
2-45
w
—
—
07/05/07—pattie
X
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст