Volkswagen Golf / Golf GTI / Jetta. Manual — part 360
01-122
Switch to measuring range:
Resistance measurement 200
Test
step
V.A.G
1598
sockets
Item tested
Test
conditions
- Additional
operations
Specification Measures for
deviations from
specification
15
-
Resistance
of K wire for
V.A.G 1551
connector
T16
1)
Ignition
switched off
- Disconnect
multi-pin
connector from
ABS control
module (w/EDL) -
J104-
max. 1.5
- Check wiring
using wiring
diagram
Electrical
Wiring Diagrams,
Troubleshooting
& Component
Locations binder
- Connect test
box V.A.G
1598/21
- Connect
multimeter V.A.G
1526 to contacts
T16/7
1)
and
T25/7 of multi-pin
connectors from
ABS control
module (w/EDL) -
J104- using
adapter set V.A.G
1594
1)
Diagnostic connection contact assignment
Page 01-106
.
ABS, ABS/EDL and ABS/EDL/ASR ITT Mark 20 IE, electrical check
01-123
Functional check: ABS warning light -K47-
Test
step
V.A.G
1598
sockets
Item
tested
Test
conditions
- Additional
operations
Specification
Measures for
deviations from
specification
16
-
Function
of ABS
warning
light -K47-
Switch
ignition on
ABS warning light
-K47- lights up for
approx. 2 seconds
and goes out
again
Electrical Wiring
Diagrams,
Troubleshooting &
Component
Locations binder
Repair Manual,
Body Interior,Repair
Group 70
- Check wiring
using wiring
diagram
- Malfunction in
instrument cluster
ABS, ABS/EDL and ABS/EDL/ASR ITT Mark 20 IE, electrical check
01-124
Functional check: Warning light for brake system -K118-
Test
step
V.A.G
1598
sockets
Item
tested
Test
conditions
- Additional
operations
Specification
Measures for
deviations from
specification
17
-
Function
of warning
light for
brake
system -
K118-
Brake fluid
level is OK.
Switch
ignition on
Warning light for
brake system -
K118- lights up
for approx. 2
seconds and
goes out again
Electrical Wiring
Diagrams,
Troubleshooting &
Component
Locations binder
- Check brake
fluid level warning
switch -F34- in
sealing cap
- Pull
connectors off
both front
speed sensors
- Start engine
and run at
more than
2000 rpm
Warning light -
K118- lights up
and 3 warnings
are sounded
Electrical Wiring
Diagrams,
Troubleshooting &
Component
Locations binder
Repair Manual,
Body
Interior,Repair
Group 70
- Check wiring
using wiring
diagram
- Malfunction in
instrument cluster
- Reconnect
connectors to
both front
speed sensors
again
- Check DTC
memory and
erase
ABS, ABS/EDL and ABS/EDL/ASR ITT Mark 20 IE, electrical check
01-125
Functional check: ABS hydraulic pump -V64-
Test
step
V.A.G
1598
sockets
Item
tested
Test
conditions
- Additional
operations
Specification
Measures for
deviations from
specification
18
-
Function
of ABS
hydraulic
pump -
V64-
Ignition
switched off
- Pull hydraulic
pump -V64-
connector T2 off
control module
- Connect Ground
to connector T2/1
and battery
voltage to
connector T2/2
on hydraulic
pump
Hydraulic pump
runs without
malfunction
(max. 10 secs.)
- Perform output
Diagnostic Test
Mode (DTM)
Page 01-74
.
- Replace
control module.
Hydraulic pump
does not run
Repair
Manual, Brake
System, Repair
Group 45
- Replace
hydraulic unit.
ABS, ABS/EDL and ABS/EDL/ASR ITT Mark 20 IE, electrical check
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст