Volkswagen Golf / Golf GTI / Jetta. Manual — part 378
01-188
- Press
key.
The ABS warning light -K47- goes
out.
Function is unknown or
cannot be carried out at the moment
Indicated on display
The final control diagnosis is
completed
- Press
key.
Rapid data transfer
HELP
Select function XX
Indicated on display
Note:
There is a malfunction in the
system if the ABS warning light -
K47- does not go out.
Adhere exactly to test sequence:
First check DTC memory, then
erase.
- End output (Function 06)
Page
01-231
.
On Board Diagnostic (OBD), performing
01-189
Diagnostic Trouble Code (DTC) table
Note:
When beginning On Board Diagnostic (OBD) troubleshooting of the vehicle control
modules, always start with function "Automatic test sequence" by pressing keys 0
and 0 because the control modules are interconnected with a data bus wire. This
checks the DTC memories of the control modules in the vehicle.
All the possible DTCs which can be recognized by the ABS control module (w/EDL) -
J104- and printed-out on V.A.G 1551 or VAS 5051, are listed on the following pages
according to the 5 digit DTC code.
DTC code appears (in the "Rapid data transfer" mode) only on the print-out.
Example:
DTC code P code DTC code
5 digit
5 digit
3 digit
18256
P1848
035
The 5 digit P code which may appear next to the DTC code, is for use with the On
Board Diagnosis (OBD) and may be disregarded.
The 3 digit DTC type code is a data code and may be disregarded, but the DTC type
text is of use.
Before replacing components indicated as being faulty, check all the appropriate
connectors, wiring and Ground connections using the wiring diagram.
Electrical Wiring Diagrams, Troubleshooting & Component Locations binder.
On completion of repairs always check the DTC memory with V.A.G 1551 scan tool
or the VAS 5051 and erase.
Carry out road test exceeding 20 km/h (13 mph).
After the road test check DTC memory again.
On Board Diagnostic (OBD), performing
01-190
V.A.G 1551 print-
out
Possible cause
Repair
No DTC
recognized
If "No DTC recognized" appears after carrying out repairs, On
Board Diagnostic (OBD) is ended.
If, despite "No DTC recognized" appearing in the display, the
ABS system does not function properly, then proceed as follows:
1. Carry out road test exceeding 20 km/h (13 mph),
2. Again check DTC memory, if there is still no DTC stored,
3. Continue troubleshooting without OBD and work through the
complete
Electrical check
Page 01-288
.
00003
Fault number:
00003 / literature
ABS Control Module (w/EDL) -
J104- malfunction
Repair Manual, Brake
System, Repair Group 45
- Replace ABS Control
Module (w/EDL) -J104-
On Board Diagnostic (OBD), performing
01-191
V.A.G 1551
print-out
Possible cause
Repair
00283
Left front ABS
wheel speed
sensor -G47-
1)
Electrical
malfunction in
current circuit
Open circuit in wiring
between left front ABS
wheel speed sensor -G47-
and ABS control module
(w/EDL) -J104-
Repair Manual, Brake System,
Repair Group 45; Removing and
installing parts of ABS system on
front and rear axles
- Check wiring and connections
using wiring diagram
- Perform electrical check
Page 01-288
- Read measured value block
Page 01-240
Display group
number 001
If the malfunction occurs again:
Left front ABS wheel speed
sensor -G47- faulty
Repair Manual, Brake System,
Repair Group 45
- Replace left front ABS wheel
speed sensor -G47-
1)
This DTC is recognized when vehicle is stationary.
On Board Diagnostic (OBD), performing
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст