Volkswagen Golf / Golf GTI / Jetta. Manual — part 1041
01-75
List of available functions
Function
page
01 -
Check Control Module
version
Page 01-
72
02 -
Check DTC memory
Page 01-
76
03 -
Output Diagnostic Test
Mode
Page 01-
86
05 -
Erase DTC memory
Page 01-
92
06 -
End Output
Page 01-
94
07 -
Code control module 05.99
05.00
Page 01-
95
07 Code control module 05.00
Page 01-
99
08 -
Read Measuring Value
Block
Page 01-
104
10 -
Adaptation
Page 01-
118
Notes:
Press HELP button to print out a complete list
of available functions. This list indicates
function capability of VAG 1551 Scan Tool (ST)
only, and does not necessarily reflect function
capability of vehicle systems equipped with
OBD. For instrument cluster address word 17,
do not attempt to select functions other than
those listed above.
After function is completed and forwarded with
button, VAG 1551 Scan Tool (ST) returns to
following start position:
Rapid data transfer
HELP
Select function XX
Indicated on display:
Instrument cluster m.y. 2000 through m.y. 2001, On Board Diagnostic (OBD)
13/2/2005
01-76
Diagnostic Trouble Code (DTC) memory,
checking (function 02)
Note:
DTCs stored in memory along with
corresponding malfunction descriptions can only
be displayed by initiating the On Board
Diagnostic program and checking DTC memory
(function 02).
- Connect VAG 1551 Scan Tool, select operating
mode 1 "Rapid data transfer", switch on ignition
and enter address word 17, "Instrument cluster".
- Press -Q- button to confirm input.
- Press
button until "Select function" appears
in display.
- Switch on printer with the PRINT button
(indicator lamp in button lights up).
Rapid data transfer
HELP
Select function XX
Indicated on display:
- Press buttons -0- and -2- to select "Check DTC
memory" function 02.
Rapid data transfer
Q
02 - Check DTC memory
Indicated on display:
- Press -Q- button to confirm input.
X DTC's recognized!
The number of stored DTCs appears in the
display.
Stored DTCs are displayed and printed out one
after another.
Instrument cluster m.y. 2000 through m.y. 2001, On Board Diagnostic (OBD)
13/2/2005
01-77
- Check print-out against DTC table and repair all
malfunctions as necessary
Page 01-78
.
No DTC recognized!
If "No DTC recognized" is displayed the program
will return to the initial position after pressing
button.
Rapid data transfer
HELP
Select function XX
Indicated on display:
If something else is displayed:
Scan tool operating instructions
- End Output (function 06)
Page 01-94
.
- Switch ignition off
- Disconnect VAG 1551 from Data Link Connector
(DLC).
Instrument cluster m.y. 2000 through m.y. 2001, On Board Diagnostic (OBD)
13/2/2005
01-78
Diagnostic Trouble Code (DTC) table
Notes:
The following table lists all malfunctions, with the corresponding 5 digit code
numbers, that can be recognized by control module with indicator unit in instrument
cluster insert -J285- and printed out by the VAG 1551 Scan Tool (ST).
If malfunctions do not occur regularly, these are displayed as occurring sporadically
("SP").
DTC codes appear only on print-out.
Before replacing components, check the wiring and connections to these
components as well as ground connections, according to wiring diagram.
When repair has been carried out, the Diagnostic Trouble Code (DTC) memory must
always be erased and checked again with VAG 1551 Scan Tool (ST).
If there is a specific complaint and no malfunctions are recognized after checking
Diagnostic Trouble Code (DTC) memory, carry out function 03, "Output Diagnostic
Test Mode (DTM)"
Page 01-86
or function 08, "Read measuring value block"
Page 01-104
.
Instrument cluster m.y. 2000 through m.y. 2001, On Board Diagnostic (OBD)
13/2/2005
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст