Volkswagen Golf / Golf GTI / Jetta. Manual — part 156
01-166
System in basic setting 36
1
2
Indicated on display: (1...2
display
zones)
If the diagnosis is initiated by the
Motronic Engine Control Module
(ECM) -J220- the display in display
zone 2 jumps from "Test OFF" to
"Test ON".
Note:
This process can take approx. 30
seconds.
If "B1 P2 n.OK." appears in display
zone 4:
- Leave engine running at idle until
display zone 2 shows
specification "B1 P2 OK.".
- Press
button.
- Check DTC memory, repair
Diagnostic Trouble Codes (DTCs)
if necessary and then erase DTC
memory
Page 01-23
, DTC
memory, checking and erasing.
- Read readiness code
Page 01-
146
. If the DTC memory has
been erased or the Motronic
Engine Control Module (ECM) -
J220- was disconnected from
battery (B+) positive, the
readiness code must be
generated again
Page 01-149
.
Readiness code
01-167
If no DTC is stored:
- Check Oxygen Sensor (O2S) and Oxygen
Sensor (O2S) control after Three Way Catalytic
Converter (TWC)
Page 24-140
If "B1 P2 OK." appears in display zone 4:
- Press -C- button.
Work step 12: Three Way Catalytic Converter
(TWC) diagnosis (checking conversion)
Note:
The diagnosis will only be ended if the Oxygen
Sensor (O2S) aging diagnosis for Oxygen
Sensor (O2S)s before and after Three Way
Catalytic Converter (TWC) is first successfully
completed.
Basic setting
Input display group number XXX
Indicated on display:
- Press buttons -0-, -4- and -6- for "Display group
number 46" and confirm entry with -Q- button.
System in basic setting 46
1
2
3
4
Indicated on display: (1 to 4
display zones)
- Depress brake pedal and hold.
- Depress accelerator down to wide open throttle
position.
Engine speed will be increased by Motronic
Engine Control Module (ECM) -J220- to approx.
2300 rpm.
Readiness code
01-168
Only continue with the test when:
The Three Way Catalytic Converter (TWC)
temperature is above 380 C (display zone
2).
- Depress brake pedal and accelerator down and
hold until display in display zone 4 jumps from
"Test OFF" to "Test ON".
Note:
This process can take approx. 80 seconds.
- Depress and hold brake pedal and accelerator
until display zone 4 displays specification "Cat.
B1 OK.".
- Release brake and accelerator pedals.
If "CatB1 n.OK." appears in display zone 4:
- Press
button.
- Check DTC memory, repair Diagnostic Trouble
Codes (DTCs) if necessary and then erase DTC
memory
Page 01-23
, DTC memory, checking
and erasing.
Readiness code
01-169
- Read readiness code
Page 01-146
. If the
DTC memory has been erased or the Motronic
Engine Control Module (ECM) -J220- was
disconnected from battery (B+) positive, the
readiness code must be generated again
Page 01-149
.
If no DTC is stored:
- Press buttons -0- and -6- for the function "End
output" and confirm entry with the -Q- button.
- Switch off ignition.
- Replace front exhaust pipe with Three Way
Catalytic Converter (TWC):
Repair Manual, 2.8 Liter VR6 4V Engine
Mechanical, Engine Code(s): BDF; Repair Group
26
If "Cat B1 OK." appears in display zone 4:
- Press -C- button.
Work step 13: Fuel supply system diagnosis
(idle speed)
Basic setting
Input display group number XXX
Indicated on display:
- Press buttons -2-, -1- and -6- for "Display group
number 216" and confirm entry with -Q- button.
Readiness code
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст