Volkswagen Golf / Golf GTI / Jetta. Manual — part 1027
01-21
- If a malfunction is determined when performing
Output DTM, exchange instrument cluster.
- If no malfunction is determined when performing
Output DTM, check wiring and connections to
instrument cluster using wiring diagram.
Output Diagnostic Test Mode (DTM), initiating
Notes:
Output Diagnostic Test Mode (DTM) cannot be
initiated, or will be interrupted if engine is
running or vehicle is moving.
Us the -C- button to exit the test sequence at
any time.
- Connect scan tool VAG 1551, select operating
mode 1 "Rapid data transfer", switch on ignition
and enter address word 17 "instrument cluster".
- Press -Q- button to confirm input.
- Press
button until "Select function"is shown
in display.
Rapid data transfer
HELP
Select function XX
Indicated on display:
- Press buttons -0- and -3- to select "Output
Diagnostic Test Mode" function 03.
Rapid data transfer
Q
03 - Output Diagnostic Test Mode
Indicated on display
Instrument cluster through m.y. 1999, On Board Diagnostic (OBD)
13/2/2005
01-22
- Press -Q- button to confirm input.
Rapid data transfer
Analog display
Indicated on display
After pressing the -Q- button, the
following instrument functional
checks are carried out
simultaneously on VDO instrument
clusters and sequentially on
Motometer instrument clusters
(press
button to advance through
test sequence):
After sweep of display ranges, the
following fixed values are displayed:
coolant temperature needle
moves over complete display
range
tachometer needle moves over
complete display range
speedometer needle moves over
complete display range
fuel gauge needle moves over
complete display range
Coolant temperature
gauge:
90 C
Tachometer:
3000 rpm
Speedometer:
100 km/h
(62mph)
Fuel gauge:
1
/
2
- Press
button.
Instrument cluster through m.y. 1999, On Board Diagnostic (OBD)
13/2/2005
01-23
Output Diagnostic Test Mode
Combi instrument warning lamp test
Indicated on display:
The warning lamps for
are activated and remain constantly
lit.
Brake system (low brake fluid
level, ABS inoperative)
Coolant temperature/low coolant
level indicator
Brake pad wear (where
applicable)
Fuel reserve
Oil pressure
- Press
button.
Output Diagnostic Test Mode
Seat belt warning lamp - K19
Indicated on display:
The Seat Belt Warning Light -K19-
lights up.
- Press
button.
Output Diagnostic Test Mode
SIgnal
Indicated on display:
The buzzer/chime is activated: a
warning tone sounds in intervals.
- Press
button.
Output Diagnostic Test Mode
Segment test
Indicated on display:
All segments of LCD display in
speedometer and tachometer are
activated and become visible.
Instrument cluster through m.y. 1999, On Board Diagnostic (OBD)
13/2/2005
01-24
- Press
button.
Output Diagnostic Test Mode
Coolant, excessive temp test
Indicated on display:
Instrument cluster VDO:
Safety cut-off (A/C compressor cut-
off- is activated approx. 5 seconds
later (vehicles with A/C only)
No indication is given in instrument
cluster!
Instrument cluster MMO:
Engine Coolant Temperature (ECT)
warning lamp lights and warning
sound is given.
Safety cut-off (A/C compressor cut-
off- is activated approx. 5 seconds
later (vehicles with A/C only)
- Press
button.
Output Diagnostic Test Mode
END
Indicated on display:
- Press
button.
Output Diagnostic Test Mode
END
Indicated on display, instrument
cluster MMO:
Function is unknown or
cannot be carried out at the moment
Indicated on display, instrument
cluster VDO:
End Output Diagnostic Test Mode
for VDO instrument clusters by
pressing
button.
Instrument cluster through m.y. 1999, On Board Diagnostic (OBD)
13/2/2005
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст