Volkswagen Golf / Golf GTI / Jetta. Manual — part 340
01-22
Test requirements
The tires installed to all wheels must be
of the same (approved) size; tires
inflated to prescribed pressure.
Mechanical/hydraulic parts of the brake
system including brake light switch and
brake lights OK.
Hydraulic lines and connections not
leaking (visual check of hydraulic unit,
brake calipers, wheel cylinders, tandem
master brake cylinder).
Wheel bearings and wheel bearing play
OK.
ABS control module (w/EDL) -J104- is
correctly bolted to hydraulic unit -N55-.
Connector on ABS control module
(w/EDL) -J104- correctly plugged-in
(retainer is engaged).
Check contacts of ABS components for
damage and correct seating.
All fuses OK according to wiring diagram
(remove fuse from fuse holder to check).
Supply voltage OK (at least 10.0 V).
ABS ITT Mk 20 IE On Board Diagnostic (OBD) program
01-23
V.A.G 1551 Scan Tool, connecting and
selecting function
Note:
All functions which could previously be
performed with V.A.G 1551 can also be
performed with the new tester VAS 5051.
The ABS function is switched off in the control
module during the On Board Diagnostic (OBD).
The Diagnostic Trouble Code (DTC) memory
can be erased after successful checking and
repair.
Connecting VAS 5051
Page 01-31
.
- Pull cover -1- off in direction of arrow.
- With ignition switched off connect V.A.G 1551
using cable V.A.G 1551/3(A) to Data Link
Connector
V.A.G - On Board Diagnostic
HELP
1 - Rapid data transfer1)
2 - Blink code output1)
Indicated on display
1)
Is displayed alternately
Note:
If there is no indication on display, check DLC,
Electrical checks
Page 01-102
, test steps 14
and 15.
Depending on the program, additional operating
information can be printed out by pressing the
HELP key of V.A.G 1551.
The
key is used for moving forward within
the program.
ABS ITT Mk 20 IE On Board Diagnostic (OBD) program
01-24
The PRINT key is used for switching on the
printer (warning lamp in key comes on).
- Switch ignition on.
- Switch on printer with Print key (indicator lamp in
key lights up).
- Press key -1- for "Rapid data transfer" operating
mode.
Rapid data transfer
HELP
Enter address word XX
Indicated on display
- Press keys -0- and -3-; 03 inputs the address
word of the vehicle system to be tested "Brake
electronics".
Rapid data transfer
Q
03 - Brake electronics
Indicated on display
- Confirm input with Q key.
1J0 907 379 D ABS 20 IE CAN 0001
Coding 03604 WSC XXXXX
Display shows e.g.
Displayed is:
e.g. (1J0 907 379 D)
Allocation of control module see Parts catalog
Electrical Wiring Diagrams, Troubleshooting &
Component Locations binder
The control module identification number.
System designation (ABS 20 IE)
Data BUS present. (CAN)
ABS ITT Mk 20 IE On Board Diagnostic (OBD) program
01-25
Control module code (03604).
Coding control module
Page 01-
58
Workshop code
V.A.G 1551 Scan Tool operating
instructions
If the control module identification
number does not appear
Summary
of selectable functions
Page 01-
27
- Press
key.
Rapid data transfer
HELP
Select function XX
Indicated on display (select function,
e.g. 02 - Check DTC memory).
Rapid data transfer
HELP
Control module does not answer!
Indicated on display
By pressing the HELP key, a list of
possible fault causes is printed out.
If "Control module does not answer!"
again appears:
- After eliminating possible causes
of malfunctions, enter the address
word 03 for "Brake electronics"
again and confirm.
Rapid data transfer
HELP
Control module does not answer!
Indicated on display
- Perform test steps 1, 2 and 3
Page 01-102
, Electrical check.
Rapid data transfer
No signal from control module!
malfunctions have occurred during
checking of control module
identification (possibly influenced
from external sources?)
ABS ITT Mk 20 IE On Board Diagnostic (OBD) program
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст