Volkswagen Golf / Golf GTI / Golf Variant. Manual — part 911
90 – Instruments
1
Instrument Cluster
1.1
Overview - Instrument Cluster
1 - Connector
❑ For the instrument clus‐
ter
2 - Instrument Cluster - KX2-
❑ With Instrument Cluster
Control Module - J285-
❑ If a LED indicator lamp
or instrument cluster il‐
lumination is faulty, the
instrument cluster must
be replaced
❑ Removing and instal‐
ling. Refer to
3 - Instrument Cluster Trim
❑ Removing and instal‐
ling. Refer to ⇒ Body
Interior; Rep. Gr. 70 ;
Instrument Panel; In‐
strument Cluster Trim,
Removing and Instal‐
ling .
4 - Upper Steering Column
Trim Panel
❑ Overview. Refer to ⇒
Body Interior; Rep. Gr.
68 ; Storage Compart‐
ments and Covers;
Overview - Steering
Column Trim Panel .
5 - Screw
❑ 3 Nm
❑ Quantity: 2
1.2
Instrument Cluster - KX2- , Removing
and Installing
General Information
All indicator lamps in the Instrument Cluster - KX2- have LEDs.
LEDs cannot be replaced separately if faulty. The Instrument
Cluster - KX2- must be replaced.
The following components are integrated inside the Instrument
Cluster - KX2- :
♦ Instrument Cluster Control Module - J285-
♦ Fuel Gauge - G1-
♦ Speedometer - G21-
♦ Engine Coolant Temperature Gauge - G3-
♦ Tachometer - G5-
♦ Indicator lamps
Do not disassemble the Instrument Cluster - KX2- .
If the control module is being replaced, use the Vehicle Diagnostic
Tester and select the “Replacing” function for the respective con‐
trol module in “Guided Fault Finding”.
Removing
For better illustration the steering wheel is not shown. It is not
necessary to remove the steering wheel in order to remove the
Instrument Cluster - KX2- .
– Position the steering wheel as far back as possible. Use the
entire adjustment range of the steering column adjustment for
this.
– Turn off the ignition and all electrical equipment.
– Remove the ignition key, if equipped.
– Remove the upper steering column trim panel. Refer to ⇒
Body Interior; Rep. Gr. 68 ; Storage Compartments and Cov‐
ers; Upper Steering Column Trim Panel, Removing and In‐
stalling .
– Remove the instrument cluster trim -1-. Refer to ⇒ Body In‐
terior; Rep. Gr. 70 ; Instrument Panel; Instrument Cluster
Trim, Removing and Installing .
– Remove the screws -3-.
Note
The Instrument Cluster - KX2- is engaged in the instrument panel.
For removal greater force is necessary.
– Remove the Instrument Cluster - KX2- -2- until it contacts the
steering wheel.
– Disengage the connector and disconnect.
– To disconnect push the circlip -1- on the connector.
– Pivot the retaining bracket in the direction of -arrow- and re‐
move from the connector.
– Remove the Instrument Cluster - KX2- on the front passenger
side between the steering wheel and the instrument panel.
Installing
Install in reverse order of removal.
Tightening Specifications
♦ Refer to
2
Horn
⇒ “2.1 Overview - Horn”, page 51
⇒ “2.2 High Tone Horn H2 / Low Tone Horn H7 , Removing and
2.1
Overview - Horn
Note
The Sedan is shown. The Wagon is identical.
1 - Bracket
❑ For the horn
❑ Removing and instal‐
ling. Refer to
2 - Bolt
❑ 18 Nm
3 - Nut
❑ 9 Nm
4 - Horn
❑ High Tone Horn - H2- is
installed on the left
❑ Low Tone Horn - H7- in
installed on the right
❑ Removing and instal‐
ling. Refer to
5 - Connector
2.2
High Tone Horn - H2- / Low Tone Horn
- H7- , Removing and Installing
The removal and installation is described for the left side. Re‐
moving and installing on the right side is identical.
Removing
– Turn off the ignition and all electrical equipment.
– Remove the ignition key, if equipped.
– Remove the noise insulation. Refer to ⇒ Body Exterior; Rep.
Gr. 66 ; Noise Insulation; Overview - Noise Insulation .
– Remove the nut -1-.
– Remove the horn -3- from the bracket.
– Release and disconnect the connector -2-.
Installing
Install in reverse order of removal.
Tightening Specifications
♦ Refer to
⇒ “2.1 Overview - Horn”, page 51
Bracket with Horn, Removing
– Turn off the ignition and all electrical equipment.
– Remove the ignition key, if equipped.
– Remove the noise insulation. Refer to ⇒ Body Exterior; Rep.
Gr. 66 ; Noise Insulation; Overview - Noise Insulation .
– Remove the bolt -1-.
– Remove the bracket with the horn -3-.
– Release and disconnect the connector -2-.
Install the Bracket and Horn.
Install in reverse order of removal.
Tightening Specifications
♦ Refer to
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст