Volkswagen Golf / Golf GTI / Golf Variant. Manual — part 403
B-Pillar Lower Trim Panel
Note
The following describes the removing and installing on the left side of the vehicle. Removing and installing on
the right side is identical.
– Loosen the sill panel strip -2- near the transition area to the
lower B-pillar trim panel -1-. Refer to
⇒ “5.10 Sill Panel Strip, Removing and Installing”, page 249
.
– Loosen the upper B-pillar trim panel in the transition area to
the lower B-pillar trim panel -1-. Refer to
– Loosen the lower B-pillar trim panel -1- from the door seal
molding.
– Loosen the lower B-pillar trim panel -1- near the clips from the
body mounts using the Wedge Set - T10383- .
– If equipped, disconnect the connector from the Interior Moni‐
toring and Vehicle Inclination Deactivation Button - E616- and
remove the B-pillar lower trim panel -1-.
Installing
Note
♦
Check all the fasteners for damage and replace if necessary.
♦
Remove any remaining clips in the body mounting points using
the Omega Clip Tool - T40280- . To install, insert into the B-
pillar trim panels.
♦
Make sure that the B-pillar trim panels are inside the door seal
molding after installing.
Install in reverse order of removal.
Tightening Specifications
♦ Refer to
⇒ “5.4 Overview - B-Pillar Trim Panel”, page 240
5.14
C-Pillar Trim Panel, Removing and In‐
stalling
⇒ “5.14.1 C-Pillar-Trim Panel, Removing and Installing, Sedan”,
page 261
⇒ “5.14.2 C-Pillar-Trim Panel, Removing and Installing, Wagon”,
5.14.1
C-Pillar-Trim Panel, Removing and In‐
stalling, Sedan
Note
The following describes the removing and installing on the left
side of the vehicle. Removing and installing on the right side is
identical.
Special tools and workshop equipment required
♦ Pry Lever - 80-200-
Removing
– Remove the rear shelf compartment. Refer to
⇒ “6.9 Rear Shelf Compartment, Removing and Installing”,
– Remove the roof end strip. Refer to
⇒ “7.2 Roof End Strip, Removing and Installing”, page 299
– Unclip the C-pillar trim panel near the clips from the body
mounts using the Pry Lever - 80-200- in direction of
-arrows A-.
– Remove the C-pillar trim panel downward in direction of
-arrow B-.
Installing
Note
♦
Check all the fasteners for damage and replace if necessary.
♦
Remove any remaining clips in the body mounting points using
the Omega Clip Tool - T40280- . To install, insert into the C-
pillar trim panel.
♦
Make sure that the C-pillar trim panel is inside the rear lid seal
molding after it is installed.
Install in reverse order of removal.
5.14.2
C-Pillar-Trim Panel, Removing and In‐
stalling, Wagon
Note
The following describes the removing and installing on the left
side of the vehicle. Removing and installing on the right side is
identical.
Special tools and workshop equipment required
♦ Pry Lever - 80-200-
Caution
This procedure contains mandatory replaceable parts. Refer
to component overview prior to starting procedure.
Mandatory Replacement Parts
♦ Upper Clips -3-
Removing
– Remove the D-pillar trim panel. Refer to
⇒ “5.15 D-Pillar Trim Panel, Removing and Installing”,
.
– Remove the wheel housing trim panel. Refer to
⇒ “5.17.2 Wheel Housing Trim Panel, Removing and Instal‐
– Only loosen the luggage compartment side trim panel near the
C-pillar, D-pillar and rear side window (do not remove com‐
pletely).
– Unclip the C-pillar trim panel -1- near the clips -2- from the
body mounts using the Pry Lever - 80-200- .
– Unclip the C-pillar trim panel from the clips -3-.
– Remove the C-pillar trim panel downward in direction of
-arrow-.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст