Volkswagen Golf / Golf GTI / Golf Variant. Manual — part 965
❑ Removing and installing. Refer to
⇒ “2.29 Sunroof Button E325 , Removing and Installing”, page 274
.
2.7
Rotary Light Switch - EX1- , Removing
and Installing
Removing
– Turn off the ignition and all electrical equipment.
– Remove the ignition key, if equipped.
– Push in the Rotary Light Switch - EX1- rotary handle -1- op‐
posite the direction of the -arrow A- and turn in the direction of
the -arrow B-.
– Hold the rotary handle -1- in this position.
– Remove the entire Rotary Light Switch - EX1- in the direction
of the -arrow A- from the instrument panel.
– Disconnect the connectors -arrow A-.
– Remove the Rotary Light Switch - EX1- -1-.
Installing
Install in the reverse order of removal while paying attention to
the following:
– Tighten the Rotary Light Switch - EX1- and push in the light
switch rotary handle in direction of -arrow 1- and at the same
time turn right in direction of - arrow 2-.
– Hold the rotary handle in this position and install the Rotary
Light Switch - EX1- in the instrument panel -3-.
– Turn the rotary handle to “0” to lock the switch in the instrument
panel.
– Perform a function test.
2.8
Headlamp Range Control Adjuster -
E102- , Removing and Installing
Removing
– Turn off the ignition and all electrical equipment.
– Remove the ignition key, if equipped.
– Remove the Rotary Light Switch - EX1- . Refer to
⇒ “2.7 Rotary Light Switch EX1 , Removing and Installing”,
.
– Remove the bolt -1-.
– Remove the trim -2- using the Headlamp Range Control Ad‐
juster - E102- from the instrument panel.
– Release and disconnect the connectors.
– Push the catches on the Headlamp Range Control Adjuster -
E102- -1- in the direction of the -arrow A-.
– Push the Headlamp Range Control Adjuster - E102- -1-.
Installing
Install in reverse order of removal.
– Perform a function test.
2.9
Driving Profile Selection Button - E735- ,
Removing and Installing
Removing and installing. Refer to
⇒ “2.14 Center Console Switch Module 1 and 2 EX23 / EX30 ,
Removing and Installing”, page 267
2.10
Start/Stop Mode Button - E693- , Re‐
moving and Installing
Removing and installing. Refer to
⇒ “2.14 Center Console Switch Module 1 and 2 EX23 / EX30 ,
Removing and Installing”, page 267
2.11
ASR/ESP Button - E256- , Removing
and Installing
Removing and installing. Refer to
⇒ “2.14 Center Console Switch Module 1 and 2 EX23 / EX30 ,
Removing and Installing”, page 267
2.12
Parking Aid Button - E266- , Removing
and Installing
Removing and installing. Refer to
⇒ “2.14 Center Console Switch Module 1 and 2 EX23 / EX30 ,
Removing and Installing”, page 267
2.13
Parallel Parking Assistance Button -
E581- , Removing and Installing
Removing and installing. Refer to
⇒ “2.14 Center Console Switch Module 1 and 2 EX23 / EX30 ,
2.14
Center Console Switch Module 1 and 2
-EX23- / -EX30- , Removing and Instal‐
ling
Special tools and workshop equipment required
♦ Trim Removal Wedge - 3409-
The following buttons are installed on the left and right sides of
the selector lever, depending on the vehicle equipment, in two
button modules. The same procedure is used to remove and in‐
stall the following components. The procedure is only described
for one button module. A removed button module cannot be dis‐
assembled.
Center Console Switch Module 1 - EX23-
♦ Driving Profile Selection Button - E735-
♦ Start/Stop Mode Button - E693-
♦ ASR/ESP Button - E256-
Center Console Switch Module 2 - EX30-
♦ Parking Aid Button - E266-
♦ Parallel Parking Assistance Button - E581-
Caution
Risk of damaging the component surfaces.
♦ When positioning a prying tool, put commercially available
adhesive tape over the component in the visible area.
Removing
– Turn off the ignition and all electrical equipment.
– Remove the ignition key, if equipped.
– Remove the selector lever boot. Refer to ⇒ Rep. Gr. 34 ;
Selector Mechanism; Selector Lever Handle, Removing and
Installing .
– Pry the trim -1- up using the -3409- .
– Lift the driver side button module -1- or the front passenger
side button module -2- upward from the center console.
– Release and disconnect the connector -1-.
– Remove the button module -2-.
Installing
Install in reverse order of removal.
– Perform a function test.
2.15
Emergency Flasher Switch - EX3- , Re‐
moving and Installing
Removing
– Turn off the ignition and all electrical equipment.
– Remove the ignition key, if equipped.
– Grasp the Front Passenger Airbag -Disabled- Indicator Lamp
- K145- -1- at the side -A arrows- and remove from the instru‐
ment panel.
– Release and disconnect the connectors.
– Loosen the catches -1-.
– Push the Emergency Flasher Switch - EX3- -2- out of the Front
Passenger Airbag -Disabled- Indicator Lamp - K145- in the
direction of the -arrow A-.
Installing
Install in reverse order of removal.
– Perform a function test.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст