Volkswagen Golf / Golf GTI / Golf Variant. Manual — part 991
♦ Rearview camera housing, disconnecting from the pivoting
motor. Refer to
Rearview Camera Housing with Pivoting Motor, Removing from
Pivoting Emblem and Installing
Removing
– Remove the pivoting emblem with the rearview camera and
pivoting motor from the rear lid. Refer to ⇒ Body Exterior; Rep.
Gr. 55 ; Rear Lid; Mechanism, Removing and Installing .
– Release and disconnect the connector -5-.
– Remove bolts -arrows-.
– Remove the rearview camera housing -2- together with the
pivoting motor -3- from the pivoting emblem -4-.
Installing
Install in reverse order of removal. Note the following:
Caution
♦ Risk of leaks
♦ Water could enter the luggage compartment if the seals
are twisted or are not positioned correctly.
♦ Make sure the installed seal is in good condition and in‐
stalled correctly.
– Check the seal between the camera and pivoting emblem and
make sure it is not loose or turned.
– Insert the pivoting motor wire into the wiring guide -1- for the
rearview camera housing -2-.
– Insert the rearview camera housing -2- together with the piv‐
oting motor -3- into the pivoting emblem -4-.
Caution
♦ The pivoting mechanism may be difficult to move.
♦ The bolt in the pivoting motor that is difficult to access
-lower right arrow- may fall out when inserting it in the rear
view camera housing.
♦ The pivoting emblem must be held so that the pivoting
motor -3- is at the bottom when positioning the bolts.
– Install the bolts -arrows-.
– Install the pivoting emblem with the rearview camera and piv‐
oting motor in the rear lid. Refer to ⇒ Body Exterior; Rep. Gr.
55 ; Rear Lid; Mechanism, Removing and Installing .
Tightening Specifications
♦ Refer to
⇒ “7.3 Overview - Rearview Camera System”, page 52
Rearview Camera Housing, Disconnecting from Pivoting Motor
Special tools and workshop equipment required
♦ Torque Wrench 1783 - 2-10Nm - VAG1783-
Removing
– Rearview camera housing with pivoting motor, removing from
.
– Remove the bolts -2-.
– Carefully separate the rearview camera housing from the piv‐
oting motor.
Installing
Install in reverse order of removal. Note the following:
– Check if the release lever and the sliding surface on the piv‐
oting motor are sufficiently lubricated with grease.
– Connect the rearview camera housing and the pivoting motor.
– Install the bolts.
– Install the rear view camera housing with the pivoting motor in
.
Tightening Specifications
♦ Refer to
8
Multifunction Steering Wheel
⇒ “8.1 Overview - Multifunction Steering Wheel”, page 55
⇒ “8.2 Overview - Multifunction Steering Wheel”, page 55
⇒ “8.3 Right/Left Multifunction Buttons On Steering Wheel E441 /
E440 , Removing and Installing”, page 56
⇒ “8.4 Tiptronic Downshift Button on Steering Wheel E439 / Tip‐
tronic Upshift Button on Steering Wheel E438 , Removing and
8.1
Overview - Multifunction Steering Wheel
Buttons are integrated in the steering wheel for easier operation
of the Infotainment system, telephone, navigation, cruise control
system and vehicle menus. On vehicles with Tiptronic, rocker
switches are also installed on the left and right.
The Multifunction Steering Wheel Control Module - J453- ( Left
Multifunction Buttons on Steering Wheel - E440- ) reads out the
button information and transfers it over the LIN Bus to the Steering
Column Electronics Control Module - J527- . From the Steering
Column Electronics Control Module - J527- , the information is
transferred to the individual components via the CAN Bus (com‐
fort) and the Data Bus On Board Diagnostic Interface - J533- .
Fault finding is performed via
Guided Fault Finding
using the
Vehicle Diagnostic Tester .
8.2
Overview - Multifunction Steering Wheel
1 - Tiptronic Downshift Button
on Steering Wheel - E439-
❑ Removing and instal‐
ling. Refer to
2 - 3-Spoke Steering Wheel
3 - Tiptronic Upshift Button on
Steering Wheel - E438-
❑ Removing and instal‐
ling. Refer to
4 - Screw
❑ 1 Nm
❑ Quantity: 2
5 - Trim Molding
6 - Right Multifunction Buttons
On Steering Wheel - E441-
❑ Removing and instal‐
ling. Refer to
.
7 - Left Multifunction Buttons On Steering Wheel - E440-
❑ Removing and installing. Refer to
8 - Screw
❑ 1 Nm
❑ Quantity: 6
8.3
Right/Left Multifunction Buttons On
Steering Wheel -E441- / -E440- , Re‐
moving and Installing
Special tools and workshop equipment required
♦ Trim Removal Wedge - 3409- quantity: 2
♦ Lever - Fuel Line - T10468-
♦ Door Trim Pliers - 3392-
♦ Torque Screwdriver - VAS6494-
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст