Volkswagen Golf / Golf GTI / Golf Variant. Manual — part 950
9.6
Rear Parking Aid Sensor, Removing
and Installing
Removing
– Turn off the ignition and all electrical equipment.
– Remove the ignition key, if equipped.
Outer Sensors
The outer rear parking aid sensor can be remove and installed
without removing the rear bumper.
– Press both catches in the direction of the -arrow A- and at the
same time press sensor -1- inward from outside.
– Release and disconnect the connector -2-.
Interior Sensor
– Remove the rear bumper cover. Refer to ⇒ Body Exterior;
Rep. Gr. 63 ; Rear Bumper; Bumper Cover, Removing and
Installing .
– Press both catches in the direction of the -arrow A- and at the
same time press sensor -1- inward from outside.
– Release and disconnect the connector -2-.
Installing
Install in the reverse order of removal while paying attention to
the following:
When inserting sensor into sensor bracket, make sure that de‐
coupling ring (black silicone ring) has proper fit on the sensor
head.
Both sensor mount retaining clips must engage audibly when in‐
stalling the sensor.
10
Parallel Parking Assist
⇒ “10.1 Overview - Parallel Parking Assist”, page 206
⇒ “10.2 Control Module, Removing and Installing”, page 207
⇒ “10.3 Front Sensor, Removing and Installing”, page 208
⇒ “10.4 Rear Sensor, Removing and Installing”, page 208
10.1
Overview - Parallel Parking Assist
⇒ “10.1.1 Overview - Parallel Parking Assist, Sedan”, page 206
⇒ “10.1.2 Overview - Parallel Parking Assist, Wagon”,
10.1.1
Overview - Parallel Parking Assist, Sedan
1 - Parallel Parking Assistance
Button - E581-
❑ Removing and instal‐
ling. Refer to
.
2 - Rear Parallel Parking Assist
Sensor
❑ Left Rear Parallel Park‐
ing Assistance Sensor -
G716-
❑ Right Rear Parallel
Parking Assistance
Sensor - G717-
❑ Removing and instal‐
ling. Refer to
3 - Bracket
❑ For Parallel Parking As‐
sistance Control Module
- J791-
❑ Removing and instal‐
ling. Refer to
.
4 - Parallel Parking Assistance
Control Module - J791-
❑ Removing and instal‐
ling. Refer to
⇒ “10.2 Control Module, Removing and Installing”, page 207
5 - Parallel Parking Assist Front Sensor
❑ Left Front Parallel Parking Assistance Sensor - G568-
❑ Right Front Parallel Parking Assistance Sensor - G569-
❑ Removing and installing. Refer to
10.1.2
Overview - Parallel Parking Assist, Wagon
1 - Parallel Parking Assistance
Button - E581-
❑ Removing and instal‐
ling. Refer to
2 - Rear Parallel Parking Assist
Sensor
❑ Left Rear Parallel Park‐
ing Assistance Sensor -
G716-
❑ Right Rear Parallel
Parking Assistance
Sensor - G717-
❑ Removing and instal‐
ling. Refer to
.
3 - Bracket
❑ For Parallel Parking As‐
sistance Control Module
- J791-
❑ Removing and instal‐
ling. Refer to
4 - Parallel Parking Assistance
Control Module - J791-
❑ Removing and instal‐
⇒ “10.2 Control Module, Removing and Installing”, page 207
.
5 - Parallel Parking Assist Front Sensor
❑ Left Front Parallel Parking Assistance Sensor - G568-
❑ Right Front Parallel Parking Assistance Sensor - G569-
❑ Removing and installing. Refer to
⇒ “10.3 Front Sensor, Removing and Installing”, page 208
.
10.2
Control Module, Removing and Instal‐
ling
The removal and installation of the Parallel Parking Assistance
Control Module - J791- is identical to the removal and installation
of the Parking Aid Control Module - J446- .
– Parking Aid Control Module - J446- , Removing and installing.
Refer to
⇒ “9.2 Parking Aid Control Module J446 , Removing and In‐
.
10.3
Front Sensor, Removing and Installing
Removing
– Turn off the ignition and all electrical equipment.
– Remove the ignition key, if equipped.
– Remove the wheel housing liner. Refer to ⇒ Body Exterior;
Rep. Gr. 66 ; Wheel Housing Liner; Front Wheel Housing Lin‐
er, Removing and Installing .
– Press both catches in the direction of the -arrows A- and at the
same time press sensor -1- inward from outside.
– Release and disconnect the connector -2-.
Installing
Install in the reverse order of removal while paying attention to
the following:
When inserting sensor into sensor bracket, make sure that de‐
coupling ring (black silicone ring) has proper fit on the sensor
head.
Both sensor mount retaining clips must engage audibly when in‐
stalling the sensor.
10.4
Rear Sensor, Removing and Installing
Removing
– Turn off the ignition and all electrical equipment.
– Remove the ignition key, if equipped.
– Remove the rear wheel housing liner. Refer to ⇒ Body Exte‐
rior; Rep. Gr. 66 ; Wheel Housing Liner; Rear Wheel Housing
Liner, Removing and Installing .
– Press both catches in the direction of the -arrows A- and at the
same time press sensor -1- inward from outside.
– Release and disconnect the connector -2-.
Installing
Install in the reverse order of removal while paying attention to
the following:
When inserting sensor into sensor bracket, make sure that de‐
coupling ring (black silicone ring) has proper fit on the sensor
head.
Both sensor mount retaining clips must engage audibly when in‐
stalling the sensor.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст