Volkswagen Golf / Golf GTI / Golf Variant. Manual — part 42
5
High-Mounted Brake Lamp
⇒ “5.1 Overview - High-Mounted Brake Lamp”, page 157
⇒ “5.2 High-Mounted Brake Lamp, Removing and Installing”,
5.1
Overview - High-Mounted Brake Lamp
⇒ “5.1.1 Overview - High-Mounted Brake Lamp, Except GTI”,
page 157
⇒ “5.1.2 Overview - High-Mounted Brake Lamp, GTI”,
5.1.1
Overview - High-Mounted Brake Lamp, Except GTI
1 - Connector
2 - Washer Fluid Hose
3 - High-Mounted Brake Lamp
❑ With High-Mounted
Brake Lamp Bulb - M25-
❑ Removing and instal‐
ling. Refer to
5.1.2
Overview - High-Mounted Brake Lamp, GTI
1 - Screw
❑ 2 Nm
2 - Connector
3 - High-Mounted Brake Lamp
❑ With High-Mounted
Brake Lamp Bulb - M25-
❑ Removing and instal‐
ling. Refer to
4 - Washer Fluid Hose Con‐
nection
5 - Screw
❑ 2 Nm
6 - Screw
❑ 2 Nm
7 - Roof Edge Spoiler
❑ Roof Edge Spoiler, Re‐
moving and installing.
Refer to ⇒ Body Exteri‐
or; Rep. Gr. 66 ; Roof
Bars/Roof Rails .
5.2
High-Mounted Brake Lamp, Removing
and Installing
⇒ “5.2.1 High-Mounted Brake Lamp, Removing and Installing,
Except GTI”, page 158
⇒ “5.2.2 High-Mounted Brake Lamp, Removing and Installing,
5.2.1
High-Mounted Brake Lamp, Removing
and Installing, Except GTI
Special tools and workshop equipment required
♦ Trim Release Lever - Wedge - T10039/1-
Removing
– Turn off the ignition and all electrical equipment.
– Remove the ignition key, if equipped.
Caution
Risk of damaging the component surfaces.
♦ When positioning a prying tool, put commercially available
adhesive tape over the component in the visible area.
– Cover the area of the rear lid above the brake light with a strip
of adhesive tape -1-.
Caution
When removing the high-mounted brake lamp, ensure seal is
not damaged.
– Install the -T10039/1- -1- on top between the high-mounted
brake lamp -2- and the rear lid.
– Push the high-mounted brake lamp -2- downward using the -
T10039/1- -1-.
– Pivot out the high-mounted brake lamp -2- from the rear lid.
– Remove the hose clip -arrow-.
– Remove the hose connection -1- from the high-mounted brake
lamp.
– Release and disconnect the connector -2-.
– Remove the high-mounted brake lamp.
Installing
During installation of the high-mounted brake lamp, ensure proper
seating of the seal. Seal must not have any bulges and must not
be damaged.
– Install the hose and connectors.
– Push the high-mounted brake lamp in the rear lid.
– Engage the upper hook.
– Engage the lower springs.
– Make sure the High-Mounted Brake Lamp Bulb - M25- and the
rear window washer system are working correctly.
5.2.2
High-Mounted Brake Lamp, Removing
and Installing, GTI
Removing
– Turn off the ignition and all electrical equipment.
– Remove the ignition key, if equipped.
– Remove the spoiler on the edge of the roof. Refer to ⇒ Body
Exterior; Rep. Gr. 66 ; Roof Bars/Roof Rails .
– Remove the bolts -1, 5 and 6- from the high-mounted brake
lamp -7-.
– Lift up the catches -2 and 4- to carefully loosen.
– Slightly lift the support bracket -3-.
– Remove the high-mounted brake lamp -7- from the spoiler on
the edge of the roof.
Installing
Installation is performed in the reverse order of removal, noting
the following:
During installation of the high-mounted brake lamp, ensure proper
seating of the seal. Seal must not have any bulges and must not
be damaged.
– Make sure the High-Mounted Brake Lamp Bulb - M25- and the
rear window washer system are working correctly.
Tightening Specifications
♦ Refer to
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст