Volkswagen Golf / Golf GTI / Golf Variant. Manual — part 11
3.1.4
Overview - Starter, Vehicles with Automatic Transmission
1 - Starter - B-
❑ Removing and instal‐
ling. Refer to
.
2 - Double Bolt
❑ 80 Nm
❑ Quantity: 2
3 - Bracket
❑ For the wiring harness
4 - Connector
5 - Nut
❑ 20 Nm
❑ Quantity: 2
6 - Nut
❑ 20 Nm
7 - Cap
8 - Terminal 30/B+
9 - Bracket
❑ For the wiring harness
3.2
Starter, Removing and Installing
⇒ “3.2.1 Starter, Removing and Installing, Vehicles with Manual
Transmission”, page 33
⇒ “3.2.2 Starter, Removing and Installing, Vehicles with DSG
Transmission DQ200–7F”, page 35
⇒ “3.2.3 Starter, Removing and Installing, Vehicles with DSG
Transmission DQ250-6F”, page 36
⇒ “3.2.4 Starter, Removing and Installing, Vehicles with Automat‐
3.2.1
Starter, Removing and Installing, Vehi‐
cles with Manual Transmission
Special tools and workshop equipment required
♦ Torque Wrench 1331 5-50Nm - VAG1331-
♦ Torque Wrench 1332 40-200Nm - VAG1332-
Removing
– Disconnect the Battery - A- . Refer to
⇒ “1.3 Battery, Disconnecting and Connecting”, page 9
.
– Remove the noise insulation. Refer to ⇒ Body Exterior; Rep.
Gr. 66 ; Noise Insulation; Overview - Noise Insulation .
– If necessary, remove the air filter housing. Refer to ⇒ Rep.
Gr. 23 ; Air Filter; Air Filter Housing, Removing and Installing
or ⇒ Rep. Gr. 24 ; Air Filter; Air Filter Housing, Removing and
Installing .
– Release and disconnect the connector -1-.
– Remove the cap -2-.
– Remove the nuts -3-, and terminal 30/B+.
– If equipped remove the nut -1- from the Starter - B- upper bolt.
– If equipped remove the ground cable -2-.
– If equipped remove the nut -1- from the Starter - B- lower bolt.
– If equipped remove the ground cable -2-.
Note
The wires remain connected.
– Remove the nut -4- and remove the wiring harness bracket
-1-.
– Remove the Starter - B- -3- bolts -2 and 5- .
– Remove the Starter - B- -3- downward.
Installing
Install in the reverse order of removal while paying attention to
the following:
– Connect the Battery - A- . Refer to
⇒ “1.3 Battery, Disconnecting and Connecting”, page 9
Tightening Specifications
♦ Refer to
⇒ “3.1.1 Overview - Starter, Vehicles with Manual Transmis‐
3.2.2
Starter, Removing and Installing, Vehi‐
cles with DSG Transmission DQ200–7F
Special tools and workshop equipment required
♦ Torque Wrench 1331 5-50Nm - VAG1331-
♦ Torque Wrench 1332 40-200Nm - VAG1332-
Removing
– Disconnect the Battery - A- . Refer to
⇒ “1.3 Battery, Disconnecting and Connecting”, page 9
– If necessary, remove the air filter housing. Refer to ⇒ Rep.
Gr. 23 ; Air Filter; Air Filter Housing, Removing and Installing
or ⇒ Rep. Gr. 24 ; Air Filter; Air Filter Housing, Removing and
Installing .
– Remove the nut -1- from the upper bolt of the Starter - B- .
– Remove the ground cable -2-.
– Disconnect the connector -4-.
– Remove the cap -5-.
– Remove the nut -6- and terminal 30/B+.
– Remove the Starter - B- -3- bolts -1 and 2-.
– Remove the Starter - B- -3- upward.
Installing
Install in the reverse order of removal while paying attention to
the following:
– Connect the Battery - A- . Refer to
⇒ “1.3 Battery, Disconnecting and Connecting”, page 9
.
Tightening Specifications
♦ Refer to
⇒ “3.1.2 Overview - Starter, Vehicles with DSG Transmission
3.2.3
Starter, Removing and Installing, Vehi‐
cles with DSG Transmission DQ250-6F
Special tools and workshop equipment required
♦ Torque Wrench 1331 5-50Nm - VAG1331-
♦ Torque Wrench 1332 40-200Nm - VAG1332-
Removing
– Disconnect the Battery - A- . Refer to
⇒ “1.3 Battery, Disconnecting and Connecting”, page 9
.
– If necessary, remove the air filter housing. Refer to ⇒ Rep.
Gr. 23 ; Air Filter; Air Filter Housing, Removing and Installing
or ⇒ Rep. Gr. 24 ; Air Filter; Air Filter Housing, Removing and
Installing .
– Remove the noise insulation. Refer to ⇒ Body Exterior; Rep.
Gr. 66 ; Noise Insulation; Overview - Noise Insulation .
– Remove the nut -2- from the lower bolt for the Starter - B-
-1-.
– Remove the ground cable -3-.
– Remove the Starter - B- -1- bolt -4-.
– Disconnect the connector -3-.
– Remove the cap -4-.
– Remove the nut -5- and terminal 30/B+.
– Remove the bolt -1- for the Starter - B- -2-.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст