Volkswagen Golf / Golf GTI / Golf Variant. Manual — part 636
– Disconnect the sensor connector -1- from the transmission
connector.
– Remove the bolt from the 8-pin transmission connector.
– Remove the transmission connector with the wiring harness
outward from the transmission housing.
Install in reverse order of removal. Note the following:
– Coat the O-ring with ATF.
– Push the transmission connector with a new O-ring all the way
into the transmission.
– Tighten the bolt for the 8-pin transmission connector. For the
correct tightening specification. Refer to
.
– Install the valve body. Refer to
– Install the ATF strainer. Refer to
⇒ “1.2 ATF Strainer, Removing and Installing”, page 86
.
– Install the ATF pan. Refer to
⇒ “1.1 Oil Pan, Removing and Installing”, page 84
– Fill the ATF and check the level. Refer to
⇒ “7 Automatic Transmission Fluid”, page 73
.
2.5
Transmission Input Speed Sensor -
G182- , Removing and Installing
– Remove the valve body. Refer to
⇒ “2.2 Valve Body, Removing and Installing”, page 90
.
– Remove the bolt -1- from the Transmission Input Speed Sen‐
sor - G182- .
– Remove the Transmission Input Speed Sensor - G182- from
the transmission housing.
Install in reverse order of removal. Note the following:
– Push the Transmission Input Speed Sensor - G182- all the
way into the transmission housing.
– Install the bolt -1- for the Transmission Input Speed Sensor -
G182- . For the correct tightening specification. Refer to
– Install the valve body. Refer to
Tightening Specifications
♦ Refer to
⇒ “2.1 Overview - Valve Body”, page 87
2.6
Transmission Output Speed Sensor -
G195- , Removing and Installing
– Remove the valve body. Refer to
⇒ “2.2 Valve Body, Removing and Installing”, page 90
.
– Remove the bolt -2- from the Transmission Output Speed
Sensor - G195- .
– Remove the Transmission Output Speed Sensor - G195- from
the transmission housing.
Install in reverse order of removal. Note the following:
– Push the Transmission Output Speed Sensor - G195- all the
way into the transmission housing.
– Install the bolt -2- for the Transmission Output Speed Sensor
- G195- . Tightening specification. Refer to
.
– Install the valve body. Refer to
.
Tightening Specifications
♦ Refer to
3
Special Tools
Special tools and workshop equipment required
♦ Used Oil Collection and Extraction Unit - SMN372500-
♦ Torque Wrench 1783 - 2-10Nm - VAG1783-
♦ Not Illustrated:
♦ Used Oil Collection and Extraction Unit - SMN372500- or Drip
Tray - VAS6208-
39 – Final Drive, Differential
1
Seals
⇒ “1.1 Component Location Overview - Seals”, page 104
⇒ “1.2 Left Seal, Replacing”, page 104
⇒ “1.3 Right Seal, Replacing”, page 106
1.1
Component Location Overview - Seals
1 - Torque Converter Seal
❑ Replacing. Refer to
2 - Right Seal
❑ For the right flange shaft
❑ Replacing. Refer to
3 - Gearshift Shaft Seal
❑ Replacing. Refer to
4 - Left Seal
❑ For the left flange shaft
❑ Replacing. Refer to
.
1.2
Left Seal, Replacing
Special tools and workshop equipment required
♦ Shop Crane - Drip Tray - VAS6208-
♦ Puller - Unit Injector - T10055-
♦ Seal Installer - Flange Shaft Oil Seal LH - T10176-
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст