Volkswagen Golf / Golf GTI / Golf Variant. Manual — part 378
10
Airbag Crash Sensors
⇒ “10.1 Component Location Overview - Airbag Crash Sensors”,
page 160
⇒ “10.2 Driver Front Airbag Crash Sensor G283 , Removing and
Installing”, page 161
⇒ “10.3 Passenger Side Front Airbag Crash Sensor G284 , Re‐
moving and Installing”, page 164
⇒ “10.4 Driver Side Airbag Crash Sensor G179 / Front Passenger
Side Airbag Crash Sensor G180 , Removing and Installing”, page
166
⇒ “10.5 Driver Side Rear Side Airbag Crash Sensor G256 / Pas‐
senger Side Rear Side Airbag Crash Sensor G257 , Removing
10.1
Component Location Overview - Airbag Crash Sensors
1 - Front Passenger Side Air‐
bag Crash Sensor - G180-
❑ Component location: in‐
side the door
❑ For the safety precau‐
tions for working with
front side airbag crash
sensors (pressure sen‐
sors). Refer to
❑ Removing and instal‐
ling. Refer to
2 - Passenger Side Rear Side
Airbag Crash Sensor - G257-
❑ Component location:
under the wheel hous‐
ing trim panel
❑ Removing and instal‐
ling. Refer to
.
3 - Screw
❑ 9 Nm
4 - Screw
❑ 9 Nm
5 - Driver Side Rear Side Airbag Crash Sensor - G256-
❑ Component location: under the wheel housing trim panel
❑ Removing and installing. Refer to
⇒ “10.5 Driver Side Rear Side Airbag Crash Sensor G256 / Passenger Side Rear Side Airbag Crash
Sensor G257 , Removing and Installing”, page 169
6 - Driver Side Airbag Crash Sensor - G179-
❑ Component location: inside the door
❑ For the safety precautions for working with front side airbag crash sensors (pressure sensors). Refer to
⇒ “1.6 Front Side Airbag Crash Sensors (Pressure Sensors) Safety Precautions”, page 7
.
❑ Removing and installing. Refer to
⇒ “10.4 Driver Side Airbag Crash Sensor G179 / Front Passenger Side Airbag Crash Sensor G180 ,
Removing and Installing”, page 166
7 - Driver Front Airbag Crash Sensor - G283-
❑ Removing and installing. Refer to
⇒ “10.2 Driver Front Airbag Crash Sensor G283 , Removing and Installing”, page 161
.
8 - Screw
❑ 9 Nm
9 - Passenger Side Front Airbag Crash Sensor - G284-
❑ Removing and installing. Refer to
⇒ “10.3 Passenger Side Front Airbag Crash Sensor G284 , Removing and Installing”, page 164
.
10 - Screw
❑ 9 Nm
10.2
Driver Front Airbag Crash Sensor -
G283- , Removing and Installing
Removing
WARNING
Observe the safety precautions for pyrotechnical components.
Refer
to
⇒ “1.2 Safety Precautions for Pyrotechnic Components”, page
There is a risk of injury if the engine starts automatically in ve‐
hicles with the Start/Stop System.
♦ For vehicles with an activated Start/Stop system (recog‐
nized by a signal in the instrument cluster), the engine can
be started automatically if needed.
♦ Make sure that the Start/Stop System is disabled when
working on the vehicle (turn off ignition, if needed, turn the
ignition back on).
– Disconnect the battery ground cable with the ignition turned
on. Refer to ⇒ Electrical Equipment; Rep. Gr. 27 ; Battery;
Battery, Disconnecting and Connecting .
– Open the hood.
– If necessary, remove the air filter housing. Refer to ⇒ Rep.
Gr. 23 ; Air Filter or ⇒ Rep. Gr. 24 ; Air Filter .
– Disengage the washer fluid reservoir filler tube from the sup‐
port. Refer to ⇒ Electrical Equipment; Rep. Gr. 92 ; Wind‐
shield Washer System; Washer Fluid Reservoir, Removing
and Installing .
– Remove the screw -2- and the front airbag crash sensor -1-
from the lock carrier.
WARNING
Before handling pyrotechnic components (for example, dis‐
connecting the connector), the person handling it must “dis‐
charge static electricity”. This can be done by touching the door
striker pin, for example.
– Disconnect the connector -3-.
– To do this pull out the connector lock -2- and push down in
direction of -arrow-, disconnect the connector -1- on the crash
sensor.
Installing
WARNING
♦ Observe the safety precautions for pyrotechnical compo‐
nents. Refer to
⇒ “1.2 Safety Precautions for Pyrotechnic Components”,
♦ Before handling pyrotechnic components (for example,
connecting the connector), the person handling it must
“discharge static electricity”. This can be done by touching
the door striker pin, for example.
– Connect the connector -1- to the crash sensor until it clicks into
place -arrow-.
– Push in the connector lock -2- to secure the connector.
Installation is performed in reverse order of removal, while noting
the following:
Note
♦
Make sure the connectors are pushed in all the way and that
they engage audibly.
♦
Make sure the wires are not pinched.
WARNING
The ignition must be on when connecting the battery. If pyro‐
technic components (for example, airbag, belt tensioner) are
not repaired correctly, they may deploy unintentionally after
connecting battery. There must not be anyone inside the ve‐
hicle when connecting the battery.
– Connect the battery ground cable with the ignition turned on.
Refer to ⇒ Electrical Equipment; Rep. Gr. 27 ; Battery; Bat‐
tery, Disconnecting and Connecting .
WARNING
If the ignition is not switched on after the battery is reconnected
- “indicator lamps in the instrument cluster do not light up” - the
ignition (key/button) may only be switched on when the driver
seat is positioned all the way back.
Note
If the Airbag Indicator Lamp - K75- indicates a fault, check the
DTC memory, erase it and check it again using the Vehicle Di‐
agnostic Tester .
Tightening Specifications
♦ Refer to
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст