Volkswagen Golf / Golf GTI / Golf Variant. Manual — part 697
1 - Connection
2 - O-Ring
❑ Replace after removing
❑ Coat with coolant
3 - Centering Pin
4 - Bolt
❑ Tightening specification
and sequence. Refer to
5 - Seal
❑ Replace after removing
6 - Coolant Pump
❑ Removing and instal‐
ling. Refer to
❑ With a new coolant
pump, remove the pro‐
tective cap
7 - Bolt
❑ Tightening sequence.
Refer to
8 - Toothed Belt
❑ For the coolant pump
❑ Removing and installing. Refer to
⇒ “2.8 Coolant Pump Toothed Belt, Removing and Installing”, page 235
9 - Bolt
❑ 9 Nm
10 - Toothed Belt Cover
11 - Bolt
❑ 10 Nm + 90°
❑ Left thread
❑ Replace after removing
12 - Drive Gear for Toothed Belt
❑ Pay attention to the installed position.
13 - Balance Shaft Seal Intake Side
❑ Replacing. Refer to
⇒ “4.3 Balance Shaft Sealing Ring, Replacing, Intake Side”, page 75
.
14 - Balance Shaft
15 - Seal
❑ Replace after removing
16 - Bolt
❑ 9 Nm
17 - Connecting Piece
18 - Spring
19 - Seal
❑ Replace after removing
20 - Engine Temperature Control Actuator - N493-
❑ Removing and installing. Refer to
⇒ “2.9 Engine Temperature Control Actuator N493 , Removing and Installing”, page 237
Engine Temperature Control Actuator - N493- - Tightening Spec‐
ifications and Sequence
– Tighten the bolts in the sequence -1 through 5-.
Tightening Sequence
Tightening Specification
-1- through -5-
Tighten to 9 Nm.
Coolant Pump - Tightening Specification and Sequence
– Tighten the coolant pump bolts in the sequence
-1 through 4-.
Tightening Sequence
Tightening Specification
-1 through 4-
Tighten to 9 Nm.
2.2
Overview - Electric Coolant Pump
After-Run Coolant Pump - V51- , Coolant Shut-Off Valve - N82-
1 - Coolant Hose
2 - Coolant Shut-Off Valve -
N82-
❑ Removing and instal‐
ling. Refer to
3 - After-Run Coolant Pump -
V51-
❑ With bracket
❑ Depending on the ver‐
sion there can be slight
differences.
❑ Removing and instal‐
ling. Refer to
.
4 - Bracket
❑ For After-Run Coolant
Pump - V51-
5 - Bolt
❑ 20 Nm
6 - Clamp
7 - Coolant Hoses
8 - Coolant Hose
9 - Bolt
❑ 9 Nm
Transmission Coolant Valve - N488- , Vehicles with DSG
®
Trans‐
mission
1 - Bolt
❑ 9 Nm
2 - Coolant Hose
3 - Nut
❑ 9 Nm
4 - Coolant Hose
5 - Transmission Coolant
Valve - N488-
❑ Removing and instal‐
ling. Refer to
.
6 - Bracket
❑ For the Transmission
Coolant Valve - N488-
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст