Volkswagen Golf / Golf GTI / Golf Variant. Manual — part 710
17 - Engine Speed Sensor - G28-
❑ 4 Nm + 45°
❑ Component location. Refer to
⇒ Fig. ““ Engine Speed Sensor -G28- -1- ”“ , page 282
❑ Coat the seal with oil
❑ Replace screw after removal
❑ Removing and installing. Refer to
⇒ “1.6 Engine Speed Sensor G28 , Removing and Installing”, page 361
.
18 - Connectors for
❑ Knock Sensor 1 - G61-
❑ Intake Manifold Runner Control Valve - N316-
❑ Fuel Pressure Sensor - G247-
❑ Intake Manifold Runner Position Sensor - G336-
❑ Camshaft Position Sensor - G40-
❑ Combustion chambers fuel injectors N30 to N33
❑ Component location. Refer to
⇒ Fig. ““Connectors”“ , page 282
.
19 - Low Fuel Pressure Sensor - G410-
❑ 15 Nm
❑ Install the Low Fuel Pressure Sensor - G410- with an adapter
❑ Component location. Refer to
⇒ Fig. ““View from Above”“ , page 281
.
❑ Removing and installing. Refer to
⇒ “5.4 Low Fuel Pressure Sensor G410 , Removing and Installing”, page 318
.
20 - Knock Sensor 1 - G61-
❑ 20 Nm
❑ In order to remove, the coolant pump and coolant thermostat must be removed
❑ Removing and installing. Refer to
⇒ “1.4 Knock Sensor 1 G61 , Removing and Installing”, page 359
.
21 - Intake Manifold Sensor - GX9-
❑ Consists of:
Intake Air Temperature Sensor - G42-
Manifold Absolute Pressure Sensor - G71-
❑ Component location. Refer to
⇒ Fig. ““View from Above”“ , page 281
.
22 - Throttle Valve Control Module - GX3-
❑ Consists of:
EPC Throttle Drive - G186-
EPC Throttle Drive Angle Sensor 1 - G187-
EPC Throttle Drive Angle Sensor 2 - G188-
❑ After replacing or removing and installing the Throttle Valve Control Module - GX3- must be adapted to
the Engine Control Module - J623- . Refer to Vehicle Diagnostic Tester
23 - Ignition Coils with Power Output Stages
❑ Component location. Refer to
⇒ Fig. ““Ignition Coils and Adjusting Elements”“ , page 280
❑ Removing and installing. Refer to
⇒ “1.3 Ignition Coils with Power Output Stages, Removing and Installing”, page 357
.
24 - Fuel Pressure Sensor - G247-
❑ 27 Nm
❑ Component location. Refer to
⇒ Fig. ““Fuel Pressure Sensor in the High Pressure System”“ , page 281
.
❑ Removing and installing. Refer to
⇒ “5.2 Fuel Pressure Sensor G247 , Removing and Installing”, page 314
.
25 - EVAP Canister Purge Regulator Valve 1 - N80-
❑ Component location. Refer to
⇒ Fig. ““Ignition Coils and Adjusting Elements”“ , page 280
26 - Intake Manifold Runner Position Sensor - G336-
❑ Component location. Refer to
⇒ Fig. ““ Intake Manifold Runner Position Sensor -G336- -1- ”“ , page 282
27 - Engine Coolant Temperature Sensor on Radiator Outlet - G83-
❑ Component location. Refer to
⇒ “2.3 Overview - Engine Coolant Temperature Sensor”, page 228
.
❑ Removing and installing. Refer to
⇒ “2.11 Engine Coolant Temperature Sensor on Radiator Outlet G83 , Removing and Installing”,
.
28 - Charge Air Pressure Sensor - G31-
❑ Component location. Refer to
⇒ “2.1 Overview - Charge Air System”, page 264
❑ Removing and installing. Refer to
⇒ “2.4 Charge Air Pressure Sensor G31 , Removing and Installing”, page 269
.
29 - Oil Pressure Regulation Valve - N428-
❑ Component location. Refer to
⇒ “4.2 Overview - Oil Pressure Switch/Oil Pressure Regulator Valve”, page 198
❑ Removing and installing. Refer to
⇒ “4.8 Oil Pressure Regulation Valve N428 , Removing and Installing”, page 206
.
30 - Oil Pressure Switch - F22- , Reduced Oil Pressure Switch - F378- and Piston Cooling Nozzle Control Valve
- N522-
❑ Component location. Refer to
⇒ “4.2 Overview - Oil Pressure Switch/Oil Pressure Regulator Valve”, page 198
❑ Checking. Refer to Vehicle Diagnostic Tester
❑ Removing and installing. Refer to
⇒ “4.2 Overview - Oil Pressure Switch/Oil Pressure Regulator Valve”, page 198
A - Fuel Injector, Direct Fuel Injection
❑ Component location. Refer to
⇒ Fig. ““Combustion Chambers Fuel Injectors”“ , page 280
❑ Cylinder 1 Fuel Injector - N30-
❑ Cylinder 2 Fuel Injector - N31-
❑ Cylinder 3 Fuel Injector - N32-
❑ Cylinder 4 Fuel Injector - N33-
❑ Removing and installing. Refer to
⇒ “2.2 Fuel Injectors, Removing and Installing”, page 285
.
B - Fuel Injector, Intake-Manifold Fuel Injection
❑ Only installed on vehicles with the engine codes CXDA and CHHB
❑ Component location. Refer to
⇒ Fig. ““Intake Manifold Fuel Injectors”“ , page 281
❑ Cylinder 1 Fuel Injector 2 - N532-
❑ Cylinder 2 Fuel Injector 2 - N533-
❑ Cylinder 3 Fuel Injector 2 - N534-
❑ Cylinder 4 Fuel Injector 2 - N535-
❑ Removing and installing. Refer to
⇒ “2.3 Intake Manifold-Fuel Injectors, Removing and Installing”, page 287
.
C - Fuel Pump Control Module - J538-
❑ Component location. Refer to
⇒ Fig. ““ Fuel Pump Control Module -J538- -1- ”“ , page 280
❑ Removing and installing. Refer to ⇒ Fuel Supply System; Rep. Gr. 20 ; Fuel Pump; Fuel Pump Control
Module - J538- , Removing and Installing .
D - Clutch Position Sensor - G476-
❑ Only on vehicles with a manual transmission
❑ Component location. Refer to
⇒ Fig. ““ Clutch Position Sensor -G476- -2- ”“ , page 279
.
E - Accelerator Pedal Module - GX2-
❑ Consists of:
Accelerator Pedal Position Sensor - G79-
Accelerator Pedal Position Sensor 2 - G185-
❑ Component location. Refer to
⇒ Fig. ““ Accelerator Pedal Module -GX2- ”“ , page 279
❑ Removing and installing. Refer to ⇒ Fuel Supply System; Rep. Gr. 20 ; Accelerator Pedal Mechanism;
Overview - Accelerator Pedal Mechanism .
F - Coolant Fan Control Module - J293-
❑ Installed inside the coolant fan
G - Oil Pressure Switch, Level 3 - F447-
❑ Component location. Refer to
⇒ “4.2 Overview - Oil Pressure Switch/Oil Pressure Regulator Valve”, page 198
.
❑ Checking and removing and installing. Refer to
⇒ “4.4 Reduced Oil Pressure Switch F378 , Removing and Installing”, page 200
.
H - Left Electrohydraulic Engine Mount Solenoid Valve - N144- and Right Electrohydraulic Engine Mount Sol‐
enoid Valve - N145-
❑ Not installed in all vehicles (depends on the transmission)
Accelerator Pedal Module - GX2-
2 - Accelerator Pedal Module Connector
Installed Location of the Brake Lamp Switch - F- / Brake Pedal
Switch - F63- and Vacuum Sensor - G608- .
1 - Brake Lamp Switch - F- / Brake Pedal Switch - F63-
2 - Vacuum Sensor - G608-
♦ In the engine compartment on the brake booster.
Clutch Position Sensor - G476- -2-
• On the clutch pedal bracket -arrow-.
Removing and installing. Refer to ⇒ Manual Transmission; Rep.
Gr. 30 ; Clutch Mechanism; Clutch Pedal, Removing and Instal‐
ling .
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст