Volkswagen Golf / Golf GTI / Golf Variant. Manual — part 362
1.5.2
Overview - Front Seat Belt Latch, 4-Door Sedan and Wagon
1 - Front Seat Belt Latch
❑ Removing and instal‐
ling. Refer to
.
2 - Front Seat
❑ Driver side: with Driver
Seat Belt Switch - E24-
❑ Front passenger side:
with Front Passenger
Seat Belt Switch - E25-
❑ Removing and instal‐
ling. Refer to
❑ Always replaced if the
belt tensioner has de‐
ployed when the seat
belt was buckled.
3 - Screw
❑ 40 Nm
❑ Replace the bolt if it was
removed because of an
accident when the seat
belt was buckled.
1.6
Overview - Rear Seat Belt Latch
1 - Left Dual Seat Belt Latch
❑ With Driver Side Rear
Seat Belt Switch - E258-
❑ Removing and instal‐
ling. Refer to
❑ Always replaced if the
belt tensioner has de‐
ployed when the seat
belt was buckled.
❑ When tightening push
the belt latch assembly
against the stop.
❑ Must make contact with
the stop.
2 - Center Seat Belt Latch
❑ With Center Rear Seat
Belt Switch - E609-
❑ Removing and instal‐
ling. Refer to
❑ Always replaced if the
belt tensioner has de‐
ployed when the seat
belt was buckled.
❑ When tightening push
the belt latch assembly
against the stop.
❑ Must make contact with
the stop.
3 - Right Seat Belt Latch with
Rear Center Belt End Fitting
❑ With Passenger Side Rear Seat Belt Switch - E259-
❑ Removing and installing. Refer to
⇒ “1.15 Rear Seat Belt Latch, Removing and Installing”, page 121
❑ Always replaced if the belt tensioner has deployed when the seat belt was buckled.
❑ Must lie on stop when tightening the nut.
4 - Nut
❑ 40 Nm
❑ Replace the bolt if it was removed because of an accident when the seat belt was buckled.
5 - Connector
❑ For Passenger Side Rear Seat Belt Switch - E259-
6 - Nut
❑ 40 Nm
❑ Replace the bolt if it was removed because of an accident when the seat belt was buckled.
7 - Connector
❑ For Driver Side Rear Seat Belt Switch - E258- and Center Rear Seat Belt Switch - E609- .
1.7
Front Three-Point Seat Belt, Removing
and Installing
⇒ “1.7.1 Front Three-Point Seat Belt, Removing and Installing,
without Belt End Fitting Tensioner, 2-Door Sedan”, page 98
⇒ “1.7.2 Front Three-Point Seat Belt, Removing and Installing,
without Belt End Fitting Tensioner, 4-Door Sedan and Wagon”,
page 101
⇒ “1.7.3 Front Three-Point Seat Belt, Removing and Installing,
with Belt End Fitting Tensioner”, page 103
1.7.1
Front Three-Point Seat Belt, Removing
and Installing, without Belt End Fitting
Tensioner, 2-Door Sedan
Removing
WARNING
♦ Observe the safety precautions for pyrotechnical compo‐
nents. Refer to
⇒ “1.2 Safety Precautions for Pyrotechnic Components”,
.
♦ Observe the disposal regulations for pyrotechnical com‐
ponents. Refer to
⇒ “1.3 Airbag, Belt Tensioner and Battery Cut-Out Units,
Storing, Transporting and Disposing (Pyrotechnic Com‐
.
– Disconnect the battery ground cable with the ignition turned
on. Refer to ⇒ Electrical Equipment; Rep. Gr. 27 ; Battery;
Battery, Disconnecting and Connecting .
– Remove the B-pillar upper trim panel. Refer to
⇒ “5.13.1 B-Pillar Trim Panel, Removing and Installing, 2-Door
.
– Remove the front belt end fitting. Refer to
⇒ “1.11.1 Front Belt End Fitting, Removing and Installing, with‐
out Belt End Fitting Tensioner, 2-Door Sedan”, page 116
.
– Remove the front seat belt guide. Refer to
– Remove the bolt -1-.
– Remove the seat belt guide -2- and seat belt webbing.
WARNING
Before handling pyrotechnic components (for example, dis‐
connecting the connector), the person handling it must “dis‐
charge static electricity”. This can be done by touching the door
striker pin, for example.
Vehicles without Reversible Belt Tensioner
– Release the connector lock with a small screwdriver in direc‐
tion of -arrow-, and remove the connector for the belt tensioner
igniter 1 -item 1-.
– If equipped, release and remove the second connector from
the front automatic belt retractor -2- in the same way.
– Remove the bolt -3- and the automatic belt retractor -2- from
the mount.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст