Volkswagen Golf / Golf GTI / Golf Variant. Manual — part 465
One bolt is located inside the hole for the starter -arrow-. Use
Socket - Xzn 14 - T10061- to remove the bolt.
– If there are hose and cable connections located near the en‐
gine lifting eyes for the Engine Support Bridge - 10-222A- ,
these must now be removed.
– Attach the Engine Support Bridge - 10-222A- as follows:
The following are needed:
♦ Engine Support Bridge - Engine Support 18 - 10-222A/18-
♦ Engine/Gearbox Support Shackle (2 pc.) - 10-222A/12- (quan‐
tity: 2) (are needed if the Spindles from the Engine Support
Bridge cannot be engaged in the engine lifting eyes).
♦ Engine Support Bridge - Engine Support 29 - 10-222A/29-
(quantity 2)
♦ Engine Support - Basic Set Square Pipe - T40091/1- (quantity
2)
♦ Engine Support - Basic Set Movable Joint - T40091/3- (quan‐
tity 2)
♦ Engine Support - Supplement Kit - Spindle - T40093/3- (quan‐
tity: 2)
♦ Engine Support Brackets - T40093/3-6- (quantity 2)
– Insert the Engine Support Bridge - Engine Support 29 -
10-222A/29- between the fender bolting edge and the fender
bolting plate underneath it on both sides of the vehicle.
♦ Installation position:
“L” = -1- Adapter is installed on the “right” side of the vehicle
( Adapter locks in the hole on the fender).
“R” (not illustrated here), Adapter is installed on the “left” side of
the vehicle.
The arrow -2- always points in driving direction
– Slide the Engine Support Bridge - Engine Support 18 -
10-222A/18- and two Engine Support - Basic Set Movable
Joint - T40091/3- onto the Engine Support Bridge - 10-222A- .
– Tighten the Engine Support Bridge - 10-222A- on the Engine
Support Bridge - Engine Support 29 - 10-222A/29- .
-A- = Engine Support Brackets - T40093/3-6- (⇒ next illustration).
– Remove the filler tube for the windshield washer system wash‐
er fluid reservoir. Refer to ⇒ Electrical Equipment; Rep. Gr.
92 ; Windshield Washer System; Windshield Washer Fluid
Reservoir, Removing and Installing .
– If present, remove wires from the front area of both longitudinal
members -arrow-. Do not disconnect line system.
– Place the Engine Support Brackets - T40093/3-6- on both lon‐
gitudinal members (the right longitudinal member is illustrated
here).
– If necessary, carefully unclip the A/C system pipe in the front
area. Do not disconnect the line system. Refer to ⇒ Heating,
Ventilation and Air Conditioning; Rep. Gr. 87 ; Coolant Circuit;
Component Location Overview - Coolant Circuit .
• The Engine Support Brackets - T40093/3-6- locks respectively
with the pins -A- behind the tab on the longitudinal member
-arrow-.
– Install the Engine Support - Supplement Kit - Spindle -
T40093/3- .
– Connect the Engine Support - Supplement Kit - Spindle -
T40093/3- to the Engine Support Bridge - 10-222A- using the
Engine Support - Basic Set Square Pipe - T40091/1- and ten‐
sion it (⇒ previous illustration).
– Then engage the spindles in the lifting eyes.
– Pretension the engine/transmission assembly and Engine
Support Bridge via the Spindles .
– Remove the noise insulation. Refer to ⇒ Body Exterior; Rep.
Gr. 66 ; Noise Insulation; Overview - Noise Insulation .
– Remove the lower section of the left front wheel housing liner.
Refer to ⇒ Body Exterior; Rep. Gr. 66 ; Wheel Housing Liner;
Overview - Front Wheel Housing Liner .
– Remove the wires and bracket from the front of the transmis‐
sion cover -arrows- (two M6 nuts).
– Route the wires near the transmission cover upward and tie
them up.
– If equipped, disconnect the connector -1- from the Oil Level
Thermal Sensor - G266- .
– Remove the bolts -11- and then remove the pendulum support
from the transmission.
– Secure the subframe before removing. Refer to ⇒ Suspen‐
sion, Wheels, Steering; Rep. Gr. 40 ; Subframe; Subframe,
Securing .
Note
If the subframe is not secured, a vehicle alignment must be per‐
formed later.
– Remove the subframe without the steering gear. Refer to ⇒
Suspension, Wheels, Steering; Rep. Gr. 40 ; Subframe; Sub‐
frame without Steering Gear, Removing and Installing .
– Remove both driveshafts from the transmission. Refer to ⇒
Suspension, Wheels, Steering; Rep. Gr. 40 ; Driveshaft, Re‐
moving and Installing .
– Secure the driveshafts to the suspension strut using a Ten‐
sioning Strap - T10038- .
Do not damage the surface of the shafts.
– Remove the bolts -1 and 2- from the transmission bracket
-A-.
Always replace the bolts.
– Lower the engine/transmission approximately to the dimen‐
sion -a- using the spindles on the Engine Support Bridge -
10-222A- .
Dimension -a- = approximately 50 mm
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст