Volkswagen Golf / Golf GTI / Golf Variant. Manual — part 931
3
Lamps in Exterior Rearview Mirror
⇒ “3.1 Overview - Lamps in Exterior Rearview Mirror”,
page 129
⇒ “3.2 Turn Signal, Removing and Installing”, page 130
⇒ “3.3 Exterior Rearview Mirror Entry Lamp, Removing and In‐
3.1
Overview - Lamps in Exterior Rearview Mirror
1 - Mirror Cap
❑ Removing and instal‐
ling. Refer to ⇒ Body
Exterior; Rep. Gr. 66 ;
Exterior Rearview Mir‐
ror; Mirror Cap, Remov‐
ing and Installing .
2 - Screw
❑ 1 Nm
❑ Quantity: 2
3 - Turn Signal
❑ Removing and instal‐
ling. Refer to
.
4 - Bolt
❑ 9 Nm
5 - Bolt
❑ 9 Nm
6 - Clip
7 - Cap
8 - Mirror Glass
❑ Removing and instal‐
ling. Refer to ⇒ Body
Exterior; Rep. Gr. 66 ;
Exterior Rearview Mir‐
ror; Mirror Glass, Re‐
moving and Installing .
9 - Bolt
❑ Quantity: 2
❑ Tightening specifica‐
tion. Refer to ⇒ Body Exterior; Rep. Gr. 66 ; Exterior Rearview Mirror; Overview - Exterior Rearview
Mirror .
10 - Mirror Trim
❑ Removing and installing. Refer to ⇒ Body Exterior; Rep. Gr. 66 ; Exterior Rearview Mirror; Mirror Trim,
Removing and Installing .
11 - Bolt
❑ Quantity: 3
❑ Tightening specification. Refer to ⇒ Body Exterior; Rep. Gr. 66 ; Exterior Rearview Mirror; Overview -
Exterior Rearview Mirror .
12 - Adjusting Unit
❑ Removing and installing. Refer to ⇒ Body Exterior; Rep. Gr. 66 ; Exterior Rearview Mirror; Mirror Ad‐
justing Unit, Removing and Installing .
13 - Exterior Rearview Mirror Entry Lamp
❑ Driver Entry Lamp in Exterior Rearview Mirror - W52-
❑ Front Passenger Entry Lamp in Exterior Rearview Mirror - W53-
❑ Exterior rearview mirror entry lamp, removing and installing. Refer to
⇒ “3.3 Exterior Rearview Mirror Entry Lamp, Removing and Installing”, page 132
.
14 - Mirror Base
❑ Removing and installing. Refer to ⇒ Body Exterior; Rep. Gr. 66 ; Exterior Rearview Mirror; Exterior
Rearview Mirror, Removing and Installing .
3.2
Turn Signal, Removing and Installing
Special tools and workshop equipment required
♦ Torque Wrench 1783 - 2-10Nm - VAG1783-
The removal and installation is described for the left side. Re‐
moving and installing on the right side is identical.
The entire exterior mirror turn signal must be replaced if an LED
is faulty.
Removing
– Turn off the ignition and all electrical equipment.
– Remove the ignition key, if equipped.
– Remove the mirror trim. Refer to ⇒ Body Exterior; Rep. Gr.
66 ; Exterior Rearview Mirror; Mirror Trim, Removing and In‐
stalling .
– Disconnect the connector -4-.
– Remove the bolts -3-.
– Release the mounting tab if necessary.
– Remove the turn signal -2- from the mirror base -1- upward.
Installing
Install in the reverse order of removal while paying attention to
the following:
– Perform a function test.
Tightening Specifications
♦ Refer to
3.3
Exterior Rearview Mirror Entry Lamp,
Removing and Installing
Special tools and workshop equipment required
♦ Torque Wrench 1783 - 2-10Nm - VAG1783-
The removal and installation is described for the left side. Re‐
moving and installing on the right side is identical.
The entire exterior rearview mirror entry lamp must be replaced if
the LED is faulty.
Removing
– Turn off the ignition and all electrical equipment.
– Remove the ignition key, if equipped.
– Mirror trim removing and installing. Refer to ⇒ Body Exterior;
Rep. Gr. 66 ; Exterior Rearview Mirror; Mirror Trim, Removing
and Installing .
– Pry the Driver Entry Lamp in Exterior Rearview Mirror - W52-
-1- in the direction of the -arrow A-.
– Remove the Driver Entry Lamp in Exterior Rearview Mirror -
W52- -1- in the direction of the -arrow B- from the mirror
housing.
– Push the catches -3- in the direction of the -arrow C-.
– Release and disconnect the connector -2-.
Installing
Install in the reverse order of removal while paying attention to
the following:
– Perform a function test.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст