Volkswagen Golf / Golf GTI / Golf Variant. Manual — part 497
1.2
Overview - Selector Mechanism
Note
♦
Lubricate the bearing areas and the sliding surfaces.
♦
Grease allocation. Refer to the Parts Catalog.
1 - Shift Lever Shaft with Shift
Lever Cover
2 - Clip
❑ For the relay lever
3 - Selector Shaft Seal
❑ For the selector shaft
❑ Replacing. Refer to
4 - Selector Lever
❑ Insert so that master
spline aligns with shift
rod. Refer to
❑ To install, lubricate. Re‐
fer to
❑ Adjust the shift lever
mechanism after instal‐
ling. Refer to
❑ Installed position. Refer
to
.
5 - Nut
❑ 25 Nm
❑ Replace after removing
❑ Self-locking
6 - Cable Retainer
❑ For attaching the shift cable to the transmission shift lever
❑ Adjust the shift lever mechanism after installing. Refer to
⇒ “1.6 Selector Mechanism, Adjusting”, page 71
❑ Do not interchange, cable locking mechanisms for selector cable on linkage lever and for shift cable on
transmission shift lever are different
⇒ Fig. ““Cable Retainer Allocation”“ , page 68
7 - Lock Washer
❑ Replace after removing
8 - Nut
❑ 20 Nm
❑ For the cable bracket
9 - Grommet
❑ Quantity: 3
❑ Cable mounting bracket to transmission
10 - Spacer
❑ Quantity: 3
11 - Lock Washer
❑ Replace after removing
❑ Be careful not to damage the cables when removing them
12 - Selector Cable
❑ Attach to the cable retainer
❑ Installed position. Refer to
⇒ “1.1 Selector Mechanism Installation Position”, page 59
.
13 - Shift Lever Cable
❑ Attach to the cable retainer
❑ Installed position. Refer to
⇒ “1.1 Selector Mechanism Installation Position”, page 59
.
14 - Seal
❑ Between the shift lever housing and the underbody
❑ Replace after removing the shift lever housing
❑ Self-adhesive
❑ Affix to the shift lever housing
15 - Selector Housing
16 - Hex Bolt
❑ 20 Nm
❑ Quantity: 2
❑ For the cable bracket
17 - Cable Mounting Bracket
❑ Adjust after installing the selector mechanism. Refer to
⇒ “1.6 Selector Mechanism, Adjusting”, page 71
.
18 - Cable Retainer
❑ For attaching the selector cable to the relay lever
❑ Adjust the shift lever mechanism after installing. Refer to
⇒ “1.6 Selector Mechanism, Adjusting”, page 71
.
❑ Do not interchange, cable locking mechanisms for selector cable on linkage lever and for shift cable on
transmission shift lever are different
❑ Allocation. Refer to
⇒ Fig. ““Cable Retainer Allocation”“ , page 68
❑ Remove from the relay lever. Refer to
⇒ Fig. ““With the Selector Relay Lever Removed: Pry the Selector Cable Retainer Out of the Selector
❑ Press onto relay lever. Refer to
⇒ Fig. ““Installing the Selector Cable Retainer on the Relay Lever”“ , page 67
19 - Selector Relay Lever
❑ Allocation. Refer to the Parts Catalog.
❑ Lubricating. Refer to
⇒ Fig. ““Relay Lever: Lubricate the Following Areas Very Carefully when Installing.”“ , page 69
❑ Installed position. Refer to
⇒ Fig. ““Selector Lever/ Relay Lever Installed Position”“ , page 68
❑ Adjust the shift lever mechanism after installing. Refer to
⇒ “1.6 Selector Mechanism, Adjusting”, page 71
.
❑ Relay lever and cable retainer, removing and installing. Refer to
⇒ Fig. ““Relay Lever with Cable Retainer, Removing and Installing”“ , page 66
20 - Sliding Shoe
1.3
Overview - Shift Lever Knob and Cover
1 - Shift Lever Housing with
Shift Lever
2 - Nut
❑ M6: 8 Nm
❑ M8: 25 Nm
3 - Bracket
❑ For the center console
❑ Overview. Refer to ⇒
Body Interior; Rep. Gr.
68 ; Center Console;
Overview - Center Con‐
sole .
4 - Bracket
❑ For the center console
❑ Overview. Refer to ⇒
Body Interior; Rep. Gr.
68 ; Center Console;
Overview - Center Con‐
sole .
5 - Noise Insulation
6 - Badge
❑ Can be carefully pried
off the plastic or leather
shift lever knob using
Trim Removal Wedge -
3409- .
7 - Gearshift Knob
❑ With boot
❑ Always replace together
❑ The shift knob and boot
cannot be separated
from each other.
❑ Removing and instal‐
ling. Refer to
⇒ “1.4 Gearshift Knob, Removing and Installingg”, page 62
8 - Center Console
❑ Overview. Refer to ⇒ Body Interior; Rep. Gr. 68 ; Center Console; Overview - Center Console .
9 - Clamp
❑ For securing the shift knob to the shift lever
❑ Replace after removing
❑ Secure on the shift lever knob using Hose Clamp Pliers - VAG1275- .
1.4
Gearshift Knob, Removing and Instal‐
lingg
Special tools and workshop equipment required
♦ Hose Clip Pliers - VAG1275A-
♦ Wedge Set - T10383-
♦ -T10383/1-
♦ or the equivalent equipment, Backrest Panel Tool - 3370-
Removing
– Use the -T10383/1- to carefully pry out the selector lever boot
from the center console insert in direction of -arrows-.
or
– Open the ashtray.
– Push the -3370- as illustrated, under the plastic frame for the
boot in the direction of -arrow 1- until stop.
– Remove boot with plastic frame from center console frame
-A- in the direction of -arrow 2-
– Roll the selector lever boot up over the shift lever knob.
– Open the clamp -arrow- and remove the shift lever knob with
the shift lever boot.
Installing
Install in reverse order of removal. Note the following:
– Press the shift lever knob and the selector lever boot all the
way up on the shift lever.
– Secure the gearshift knob on the gearshift lever with the clamp
-arrow-. Use the -VAG1275A- to do this.
1.5
Selector Mechanism, Removing and In‐
stalling
Special tools and workshop equipment required
♦ Torque Wrench 1331 5-50Nm - VAG1331-
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст