Volkswagen Golf / Golf GTI / Golf Variant. Manual — part 368
1.14
Front Seat Belt Latch, Removing and In‐
stalling
Removing
– Remove the front seat. Refer to
⇒ “2.10 Front Seat, Removing and Installing”, page 335
– Disconnect the seat belt latch connector from the connector
station underneath the seat frame.
– Loosen the wire from the seat frame.
– Remove the bolt -3- and then remove the seat belt latch -1-
from the seat -2-.
Installing
Install in reverse order of removal while paying attention to the
following:
– Position the seat belt latch -2- so that the cut-out -arrow B-
lines up with the hole -arrow A- on the seat pan -1-.
Tightening Specifications
♦ Refer to
⇒ “1.5 Overview - Front Seat Belt Latch”, page 95
1.15
Rear Seat Belt Latch, Removing and In‐
stalling
Removing
– Remove the rear bench seat. Refer to
⇒ “3.7 Bench Seat/Single Seat, Removing and Installing”,
.
Right: Seat Belt Latch with Belt End Fitting
Note
The seat belt latch with belt end fitting is a component of the rear
center seat belt.
– If equipped, disconnect the connector -2- for the seat belt
switch.
– Remove the nut -1-.
– Remove the seat belt latch -3- with the belt end fitting.
Left: Dual Seat Belt Latch
– If equipped, disconnect the connector -3- for the seat belt
switch.
– Remove the nut -2-.
– Remove the dual seat belt latch -1-.
Installing
Install in reverse order of removal.
Tightening Specifications
♦ Refer to
2
Child Seat Anchors
⇒ “2.1 Overview - Rear Child Seat Anchors”, page 122
⇒ “2.2 LATCH Child Seat Anchor Guide, Removing and Instal‐
ling”, page 123
⇒ “2.3 Top Tether, Removing and Installing”, page 123
2.1
Overview - Rear Child Seat Anchors
Outer Seat Child Seat Anchor. Refer to
Center Seat Top Tether. Refer to
⇒ Fig. ““Center Seat Top Tether”“ , page 123
Outer Seat Child Seat Anchor
1 - LATCH Child Seat Anchor
❑ Quantity: 4
❑ Welded to the under‐
body
2 - Guide
❑ For the LATCH child
seat anchor
❑ Quantity: 4
❑ Removing and instal‐
ling. Refer to
❑ Must be secure on the
anchor
3 - Cover
❑ For the LATCH child
seat anchor
❑ Quantity: 4
❑ Removing and instal‐
ling. Refer to
❑ Must be secure on the
anchor
4 - Child Seat Anchor Top
Tether
❑ Quantity: 2
❑ Welded to the backrest
frame.
5 - Cover
❑ For Top Tether child seat anchor
❑ Quantity: 2
❑ Removing and installing. Refer to
⇒ “2.3 Top Tether, Removing and Installing”, page 123
❑ Insert in the anchor and press on it until it engages audibly
❑ Can only be pushed in one position in the rear seat backrest
6 - Rear Seat Backrest
Center Seat Top Tether
1 - Top Tether
2 - Bolt, 8 Nm
3 - Cap
2.2
LATCH Child Seat Anchor Guide, Re‐
moving and Installing
Removing
– Unclip and remove the cover -1- from the LATCH child seat
anchor -arrow-.
– Push the guide -1-, corresponding to cut-out, downward and
disengage it from the LATCH child seat anchor -2-.
– Remove the guide forward -arrow-.
Installing
Install in reverse order of removal.
2.3
Top Tether, Removing and Installing
Special tools and workshop equipment required
♦ Wedge Set - T10383-
♦ Torque Wrench 1783 - 2-10Nm - VAG1783-
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст