Volkswagen Golf / Golf GTI / Golf Variant. Manual — part 889
Vehicles with Ignition Switch
The steering lock housing can be replaced. Refer to ⇒ Electrical
Equipment; Rep. Gr. 94 ; Steering Column Switch Module; Steer‐
ing Column Switch Module, Removing and Installing .
Vehicle with “Keyless Access” Keyless Locking and Starting Sys‐
tem
The Electronic Steering Column Lock Control Module - J764- can
be removed and installed. Refer to
⇒ “2.5 Electronic Steering Column Lock Control Module J764 ,
Removing and Installing”, page 348
.
Continuation for All Vehicles
WARNING
Before starting work on electrical equipment and removing
steering wheel, the following conditions must be fulfilled:
♦ The technician must electrostatic discharge. This is done
by touching a grounded metal part, for example, water
lines, heater pipe, metal carriers or a workshop hoist .
If this not done, the Electronic Steering Column Lock Control
Module - J764- could fail later.
♦ Disconnect the battery. Refer to ⇒ Electrical Equipment;
Rep. Gr. 27 ; Battery; Battery, Disconnecting and Con‐
necting .
♦ The wheels must be straight.
The airbag system may fail at a later time if these warnings are
not followed!
– Straighten the wheels.
– Pull the lever on the side of the steering column downward.
– Push the steering column as far down as possible and remove
it.
– Push lever under steering column upward again.
– Remove the airbag unit. Refer to ⇒ Body Interior; Rep. Gr.
69 ; Driver Side Airbag; Overview - Driver Side Airbag .
– Remove the steering wheel. Refer to
⇒ “1.2 Steering Wheel, Removing and Installing”, page 336
.
– Remove the upper steering column trim panel. Refer to ⇒
Body Interior; Rep. Gr. 68 ; Storage Compartments and Cov‐
ers; Upper Steering Column Trim Panel, Removing and In‐
stalling .
– Remove the lower steering column trim panel. Refer to ⇒ Body
Interior; Rep. Gr. 68 ; Storage Compartments and Covers;
Lower Steering Column Trim Panel, Removing and Installing .
– Remove the steering column switch module. Refer to ⇒ Elec‐
trical Equipment; Rep. Gr. 94 ; Steering Column Switch Mod‐
ule; Steering Column Switch Module, Removing and Instal‐
ling .
– Remove the knee airbag. Refer to ⇒ Body Interior; Rep. Gr.
69 ; Knee Airbags; Overview - Knee Airbag .
Vehicles with Ignition Switch
– Remove the connector -1- from the Anti-Theft Immobilizer
Reader Coil - D2- .
– Remove the connector -2- from the ignition/starter switch -1-.
Vehicle with “Keyless Access” Keyless Locking and Starting Sys‐
tem
– Disconnect the connector -1-.
– Unclip the wire from the retainer on the Electronic Steering
Column Lock Control Module - J764- -arrow-.
Continuation for All Vehicles
– Remove the footwell vent under the steering column. Refer to
⇒ Heating, Ventilation and Air Conditioning; Rep. Gr. 87 ; Air
Routing; Overview - Air Routing and Air Distribution in Pas‐
senger Compartment .
– Release the tab in direction of -arrow- using a small screw‐
driver.
– Remove the wiring guide -1- forward from the metal tab.
– Release the tabs -arrows- on the wiring guide -1- with a small
screwdriver.
– Remove the wiring guide -1- downward from the steering col‐
umn.
– Release the lower cable bracket -2- and remove it downward.
– Set the wire for the steering column aside.
– Remove the bolt -1- and fold the footwell trim panel -2- in the
direction of the -arrow- into the vehicle interior.
– Remove the bolt -1- from the universal joint -2-. Then remove
the universal joint in direction of -arrow-.
Caution
If the universal joint is separated from the steering gear, the
following work cannot be performed:
♦ Connect the battery.
♦ Switch on the ignition.
♦ Turning the steering gear
♦ Turning the steering column
These points must be observed, because otherwise it can
cause irreparable damage.
– Remove the bolts -1 and 2-.
– Remove the left bracket for the knee airbag -3-.
– Remove the bolts -1 and 2-.
– Remove the right bracket for the knee airbag -3-.
– Remove the bolt -1- and hold the steering column -2-.
– Disengage the steering column -1- upward from the tabs
-2 and 3- on the mounting bracket and remove it.
Caution
For correct handling and transport of steering column. Refer to
⇒ “2.3 Steering Column, Handling and Transporting”,
.
Installing
Install in reverse order of removal. Note the following:
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст