Volkswagen Golf / Golf GTI / Golf Variant. Manual — part 928
– Turn the locking mechanism -1- in the direction of the
-arrow A-.
– Remove the HID headlamp bulb -2- in the direction of the
-arrow B- from the housing.
Installing
Install in the reverse order of removal while paying attention to
the following:
Caution
There is a risk of damaging the headlamp.
♦ Do not touch glass cone of bulb with bare fingers. Fingers
will leave traces of grease on the glass which, when the
bulb is switched on, will evaporate and cloud the glass.
♦ Use clean cloth gloves to insert the bulbs.
♦ During installation, ensure proper seating of the housing
cover. Water getting in the headlamp will cause damage.
Note
Installation position: the electrical connection faces down.
– Perform a function test.
– Check and correct headlamp adjustment, if necessary. Refer
to ⇒ Maintenance ; Booklet 36.1 ; Procedure Descriptions .
Tightening Specifications
♦ Refer to
⇒ “1.1 Overview - Headlamp”, page 92
1.12
Left/Right Position Lamp Bulb - M1- / -
M3- , Removing and Installing
⇒ “1.12.1 Left/Right Position Lamp Bulb M1 / M3 , Removing and
Installing, Halogen Dual Headlamp”, page 117
⇒ “1.12.2 Left/Right Position Lamp Bulb M1 / M3 , Removing and
Installing, HID Headlamp”, page 118
1.12.1
Left/Right Position Lamp Bulb - M1- / -
M3- , Removing and Installing, Halogen
Dual Headlamp
The Left Position Lamp Bulb - M1- and the Right Position Lamp
Bulb - M3- is integrated in the Left High Beam Headlamp Bulb -
M30- and in the Right High Beam Headlamp Bulb - M32- .
– Left/Right High Beam Headlamp Bulb -M30- / -M32- , Remov‐
ing and installing. Refer to
⇒ “1.10 Left/Right High Beam Headlamp Bulb M30 / M32 ,
1.12.2
Left/Right Position Lamp Bulb - M1- / -
M3- , Removing and Installing, HID
Headlamp
The Left Position Lamp Bulb - M1- and the Right Position Lamp
Bulb - M3- is integrated in the Left Daytime Running Lamp Bulb -
L174- and in the Right Daytime Running Lamp Bulb - L175- .
– Daytime Running Lamp Bulb -L174- / -L175- , Removing and
installing. Refer to
⇒ “1.13.2 Left/Right Daytime Running Lamp Bulb L174 / L175 ,
Removing and Installing, HID Headlamp”, page 118
1.13
Left/Right Daytime Running Lamp Bulb
- L174- / -L175- , Removing and Instal‐
ling
⇒ “1.13.1 Left/Right Daytime Running Lamp Bulb L174 / L175 ,
Removing and Installing, HID Headlamp”, page 118
1.13.1
Left/Right Daytime Running Lamp Bulb
- L174- / -L175- , Removing and Instal‐
ling, Halogen Dual Headlamp
The Left Daytime Running Lamp Bulb - L174- and the Right Day‐
time Running Lamp Bulb - L175- is integrated in the Left High
Beam Headlamp Bulb - M30- and in the Right High Beam Head‐
lamp Bulb - M32- .
– Left/Right High Beam Headlamp Bulb -M30- / -M32- , Remov‐
ing and installing. Refer to
⇒ “1.10 Left/Right High Beam Headlamp Bulb M30 / M32 ,
Removing and Installing”, page 114
.
1.13.2
Left/Right Daytime Running Lamp Bulb
-L174- / -L175- , Removing and Instal‐
ling, HID Headlamp
The removal and installation is described for the left side. Re‐
moving and installing on the right side is identical.
The Left Daytime Running Lamp Bulb - L174- and the Right Day‐
time Running Lamp Bulb - L175- has the function of the Left
Position Lamp Bulb - M1- and the Right Position Lamp Bulb - M3- .
Removing
– Turn off the ignition and all electrical equipment.
– Remove the ignition key, if equipped.
– Turn the housing cover -1- in the direction of the -arrow A- and
remove from the headlamp.
– Remove the Left Daytime Running Lamp Bulb - L174- on the
handle -1- in the direction of the -arrow A- rearward from the
reflector.
– Remove the Left Daytime Running Lamp Bulb - L174- from the
handle.
Installing
Install in the reverse order of removal while paying attention to
the following:
Caution
There is a risk of damaging the headlamp.
♦ Do not touch glass cone of bulb with bare fingers. Fingers
will leave traces of grease on the glass which, when the
bulb is switched on, will evaporate and cloud the glass.
♦ Use clean cloth gloves to insert the bulbs.
♦ During installation, ensure proper seating of the housing
cover. Water getting in the headlamp will cause damage.
– Perform a function test.
– Check and correct headlamp adjustment, if necessary. Refer
to ⇒ Maintenance ; Booklet 36.1 ; Procedure Descriptions .
1.14
Left/Right Daytime Running Lamp and
Position Lamp LED Module - L176- / -
L177- , Removing and Installing
The Left Daytime Running Lamp and Position Lamp LED Module
- L176- / Right Daytime Running Lamp and Position Lamp LED
Module - L177- is only installed with HID headlamps.
The daytime running lamp and position lamp bulbs are LED lamps
and are integrated in the headlamp. Changing the LEDs is not
possible. The headlamp must be completely replaced.
– Headlamps, Removing and installing. Refer to
⇒ “1.2 Headlamp, Removing and Installing”, page 101
.
1.15
Left/Right Low Beam Headlamp Reflec‐
tor Motor -V294- / -V295- , Removing
and Installing
The Left Low Beam Headlamp Reflector Motor - V294- / Right
Low Beam Headlamp Reflector Motor - V295- is only installed with
HID headlamps without cornering lamps.
The low beam headlamp reflector motor sits in the headlamp and
cannot be replaced separately if it is faulty.
– Headlamps, Removing and installing. Refer to
⇒ “1.2 Headlamp, Removing and Installing”, page 101
.
1.16
Left/Right Cornering Lamp Bulb - L148- /
-L149- , Removing and Installing
The Left Cornering Lamp Bulb - L148- / Right Cornering Lamp
Bulb - L149- is only installed with HID headlamps.
The removal and installation is described for the left side. Re‐
moving and installing on the right side is identical.
Removing
– Turn off the ignition and all electrical equipment.
– Remove the ignition key, if equipped.
– Turn the housing cover -1- in the direction of the -arrow A- and
remove from the headlamp.
– Push upward in the direction of the -arrow A- on the bulb sock‐
et -1-.
– Remove the bulb socket -1- from the reflector -2-.
– Disconnect the connector.
Installing
Install in the reverse order of removal while paying attention to
the following:
Caution
There is a risk of damaging the headlamp.
♦ Do not touch glass cone of bulb with bare fingers. Fingers
will leave traces of grease on the glass which, when the
bulb is switched on, will evaporate and cloud the glass.
♦ Use clean cloth gloves to insert the bulbs.
♦ During installation, ensure proper seating of the housing
cover. Water getting in the headlamp will cause damage.
– Perform a function test.
– Check and correct headlamp adjustment, if necessary. Refer
to ⇒ Maintenance ; Booklet 36.1 ; Procedure Descriptions .
1.17
Left/Right HID Headlamp Control Mod‐
ule - J343- / -J344- , Removing and In‐
stalling
The removal and installation is described for the left side. Re‐
moving and installing on the right side is identical.
WARNING
High voltage poses a life-endangering risk, injury risk and en‐
vironmental hazard.
♦ Pay attention to usage and safety information for HID
headlamps. Refer to
⇒ “1.3 HID Headlamps Usage and Safety Precautions”,
.
♦ It is necessary to disconnect the battery wire strap before
working on HID headlamp components. These parts are
marked with yellow high voltage symbols.
Removing
– Turn off the ignition and all electrical equipment.
– Remove the ignition key, if equipped.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст