Volkswagen Golf / Golf GTI / Golf Variant. Manual — part 939
6
License Plate Lamp
⇒ “6.1 Left/Right License Plate Lamp X4 / X5 , Removing and
Installing”, page 161
⇒ “6.2 Left/Right License Plate Lamp Bulb X4 / X5 , Removing
6.1
Left/Right License Plate Lamp - X4- / -
X5- , Removing and Installing
⇒ “6.1.1 Left/Right License Plate Lamp X4 / X5 , Removing and
Installing, Sedan”, page 161
⇒ “6.1.2 Left/Right License Plate Lamp X4 / X5 , Removing and
Installing, Wagon with LED”, page 161
⇒ “6.1.3 Left/Right License Plate Lamp X4 / X5 , Removing and
Installing, Wagon with Bulb”, page 162
6.1.1
Left/Right License Plate Lamp -X4- / -
X5- , Removing and Installing, Sedan
The entire license plate lamp must be replaced if a license plate
lamp LED is faulty.
Removing
– Turn off the ignition and all electrical equipment.
– Remove the ignition key, if equipped.
– Press the tab in the direction of -arrow- and remove the license
plate lamp downward from the bumper cover.
– Disconnect the connector -arrow-.
Installing
Install in the reverse order of removal while paying attention to
the following:
Insert the license plate lamp into the bumper cover so that the
connector is facing toward the left side of the vehicle.
– Perform a function test.
6.1.2
Left/Right License Plate Lamp -X4- / -
X5- , Removing and Installing, Wagon
with LED
The entire license plate lamp must be replaced if a license plate
lamp LED is faulty.
Removing
– Turn off the ignition and all electrical equipment.
– Remove the ignition key, if equipped.
– Press the Left License Plate Lamp - X4- in the direction of the
-arrow A- using a suitable tool.
– Fold the Left License Plate Lamp - X4- in the direction of the
-arrow B- out of the rear lid.
– Release and disconnect the connector -1-.
– Remove the Left License Plate Lamp - X4- -2-.
Installing
Install in the reverse order of removal while paying attention to
the following:
Insert the license plate lamp into the rear lid so that the clip is
facing toward the right side of the vehicle.
– Perform a function test.
6.1.3
Left/Right License Plate Lamp -X4- / -
X5- , Removing and Installing, Wagon
with Bulb
The entire license plate lamp must be replaced if a license plate
lamp LED is faulty.
Removing
– Turn off the ignition and all electrical equipment.
– Remove the ignition key, if equipped.
– Press the Left License Plate Lamp - X4- in the direction of the
-arrow A- using a suitable tool.
– Fold the Left License Plate Lamp - X4- in the direction of the
-arrow B- out of the rear lid.
– Press the connector safety catch -1- in the direction of the
-arrow A-.
– Disconnect the connector -2-.
Installing
Install in the reverse order of removal while paying attention to
the following:
Insert the Left License Plate Lamp - X4- into the rear lid so that
the connector is facing toward the right side of the vehicle.
– Insert the Left License Plate Lamp - X4- in the direction of the
-arrow 1- into the rear lid.
– Press the Left License Plate Lamp - X4- in the direction of the
-arrow 2- until it locks into place.
– Perform a function test.
6.2
Left/Right License Plate Lamp Bulb -
X4- / -X5- , Removing and Installing
⇒ “6.2.1 Left/Right License Plate Lamp Bulb X4 / X5 , Removing
and Installing, Sedan”, page 163
⇒ “6.2.2 Left/Right License Plate Lamp Bulb X4 / X5 , Removing
and Installing, Wagon”, page 164
6.2.1
Left/Right License Plate Lamp Bulb -
X4- / -X5- , Removing and Installing,
Sedan
The entire license plate lamp must be replaced if a license plate
lamp LED is faulty.
Removing
– Turn off the ignition and all electrical equipment.
– Remove the ignition key, if equipped.
– Remove the license plate lamp. Refer to
⇒ “6.1.1 Left/Right License Plate Lamp X4 / X5 , Removing
– Turn the lamp socket -1- in the direction of -arrow- to release
it and pull it out of the license plate lamp.
Installing
Installation is performed in the reverse order of removal, noting
the following:
Caution
There is a risk of damaging the lamp.
♦ Do not touch glass cone of bulb with bare fingers. Fingers
will leave traces of grease on the glass which, when the
bulb is switched on, will evaporate and cloud the glass.
♦ Use clean gloves for example to insert the bulbs.
– Perform a function test.
6.2.2
Left/Right License Plate Lamp Bulb -
X4- / -X5- , Removing and Installing,
Wagon
The entire license plate lamp must be replaced if a license plate
lamp LED is faulty.
Removing
– Turn off the ignition and all electrical equipment.
– Remove the ignition key, if equipped.
– Remove the license plate lamp. Refer to
⇒ “6.1.3 Left/Right License Plate Lamp X4 / X5 , Removing
and Installing, Wagon with Bulb”, page 162
.
– If equipped, unclip the glass base bulb cover -1- from the li‐
cense plate lamp.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст