Volkswagen Golf / Golf GTI / Golf Variant. Manual — part 525
2.2
Output Shaft, Disassembling and As‐
sembling
⇒ “2.2.1 Output Shaft, Disassembling and Assembling, 1st to 4th
Gears”, page 172
⇒ “2.2.2 Output Shaft, 5th, 6th and Reverse Gears, Disassem‐
bling and Assembling”, page 182
2.2.1
Output Shaft, Disassembling and As‐
sembling, 1st to 4th Gears
Special tools and workshop equipment required
♦ Press Plate - VW401-
♦ Press Plate - VW402-
♦ Press Piece - Rod - VW407-
♦ Press Piece - Rod - VW408A-
♦ Press Piece - Multiple Use - VW412-
♦ Press Piece - 60mm - VW415A-
♦ Holding Plate - VW309A-
♦ Holding Fixture - VW313-
♦ Transmission Support - VW353-
♦ Press Piece - Multiple Use - VW431-
♦ Press Piece - Multiple Use - VW433-
♦ Press Piece - Multiple Use - VW454-
♦ Press Piece - Multiple Use - VW512-
♦ Press Piece - 42mm - VW516-
♦ Press Piece - Multiple Use - VW519-
♦ Slide Hammer Set - VW771-
♦ Crankshaft Holding Fixture - VW801-
♦ Press Piece - Multiple Use - 40-105-
♦ Bearing Installer - Multiple Use - 40-20-
♦ Bearing Installer - Differential Bearing - 40-21-
♦ Press Piece - Multiple Use - 2050-
♦ Holding Fixture - Spacers - VW540/1B-
♦ Puller - Taper Roller Bearing - VAG1582-
♦ Puller - Taper Roller Bearing - Adapter 7 - VAG1582/7-
♦ Inductive Heater - VAS6414-
♦ Puller - Kukko Internal - 46-56mm - 21/7-
♦ Puller - Kukko Internal - 56-70mm - 21/8-
♦ Puller - Kukko Puller - 60-200mm Width, 250mm Length -
18/2-
♦ Puller - Kukko Quick Action Separating Tool - 22-115mm -
17/2-
♦ Puller - Kukko Counterstay - 22/2-
Removing the Dished Washer -A- from the Output Shaft
Installing the Dished Washer into the Output Shaft
Dimension “a” = 2 mm
Removing the Inner Race/Tapered Roller Bearing on the side of
the Clutch Housing
A - Separating Tool 22-115mm , for example, -17/2-
Installing the Inner Race/Tapered Roller Bearing on the Side of
the Clutch Housing
Removing the Outer Race / Tapered Roller Bearing from the
Clutch Housing
A - Counter Support , for example, -22/2-
B - Internal Puller 56 to 70 mm , for example, -21/8-
Installing the Outer Race/Tapered Roller Bearing in the Clutch
Housing
– Support the clutch housing with the -40-20- directly under the
bearing mount.
Remove the Inner Race/Tapered Roller Bearing on the side of the
Transmission Housing
Note the following before installing the -VAG1582- :
– Remove the inner race/tapered roller bearing locking ring on
the side facing the transmission housing.
– Place the -VW431- in the output shaft and lay the -40-105- on
top.
Installing the Inner Race/Tapered Roller Bearing on the side of
the Transmission Housing
– Choose the correct locking ring. Refer to
⇒ Fig. ““Selecting the Locking Ring”“ , page 174
Selecting the Locking Ring
– Choose and install the thickest locking ring that will fit.
Note
For the correct locking rings. Refer to the Parts Catalog.
The following circlips are available:
Thickness (mm)
1.79
1.83
1.86
1.89
1.92
1.95
1.98
Removing the Outer Race/Tapered Roller Bearing from the
Transmission Housing
A - Counter Support , for example, -22/2-
B - Internal Puller 46 to 58 mm , for example, -21/7-
Installing the Outer Race/Tapered Roller Bearing into the Trans‐
mission Housing
– Install the adjusting shim under the outer race.
– Support the transmission housing under the bearing mount
using the -2050- .
Disassembling the Output Shaft
Note
Remove the inner race/tapered roller bearing on the side of the
transmission housing. Refer to
⇒ Fig. ““Remove the Inner Race/Tapered Roller Bearing on the
side of the Transmission Housing”“ , page 174
.
– Remove the locking ring.
Removing the 3rd and 4th Gear Synchronizer Hub/Locking Collar
with the 4th Gear Wheel
– Remove the locking ring beforehand.
– Then remove the retaining ring -Item 20-
and thrust washers -Item 19-
.
– Then remove the 1st gear wheel with synchronizer ring.
On Transmissions with Reinforcement Measures, Remove the
Collar Bushing -B- Together with the 1st Gear Wheel -C-.
Note
Allocate transmission via code letters:
A - Puller - Quick Action Separating Tool - 22-115mm , for exam‐
ple -Kukko 17/2-
– Install the Separating Tool -A- underneath the helical-cut gear
teeth on the 1st gear wheel.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст