Volkswagen Golf / Golf GTI / Golf Variant. Manual — part 70
2.16
Left/Right Seat Heating Button -E653- /
-E654- , Removing and Installing
The seat heating buttons are integrated in the Heater Control
Module - J65- / A/C Control Module - J301- / Climatronic Control
Module - J255- display control head. Components cannot be re‐
placed separately if faulty.
– Heater Control Module - J65- / A/C Control Module - J301- /
Climatronic Control Module - J255- removing and installing.
Refer to ⇒ Heating, Ventilation, and Air Conditioning; Rep.
Gr. 87 ; Component Location Overview - Display And Control
Unit .
2.17
Glove Compartment Lamp Switch -
E26- , Removing and Installing
Removing
– Turn off the ignition and all electrical equipment.
– Remove the ignition key, if equipped.
– Open the glove compartment.
– Push the left and right glove compartment stop -1- in the up‐
ward direction of the -arrow-.
– Open the glove compartment lid -2-.
– Open the glove compartment lid completely in the direction of
the -arrow B- so that the steering rack -2- is removed from the
damper -1-.
– Remove the Glove Compartment Lamp Switch - E26- in the
damper -1- from the mount in the direction of the -arrow A-.
Installing
Install in reverse order of removal.
– Perform a function test.
2.18
Exterior Rearview Mirror Adjuster -
EX11- , Removing and Installing
Caution
Risk of damaging the component surfaces.
♦ When positioning a prying tool, put commercially available
adhesive tape over the component in the visible area.
Removing
– Turn off the ignition and all electrical equipment.
– Remove the ignition key, if equipped.
– Carefully release the retainers using a small screwdriver
-arrows-.
– Remove the Exterior Rearview Mirror Adjuster - EX11- -1-
from the exterior rearview mirror adjuster trim -2-.
– Release and disconnect the connectors.
– If necessity remove the Driver Interior Locking Button - E308- .
Refer to
⇒ “2.21 Driver Interior Locking Button E308 , Removing and
.
Installing
Install in the reverse order of removal while paying attention to
the following:
– If necessity install the Driver Interior Locking Button - E308- .
Refer to
⇒ “2.21 Driver Interior Locking Button E308 , Removing and
.
– Perform a function test.
2.19
Power Window Control Head in Driver
Door - E512- , Removing and Installing
Removing
– Turn off the ignition and all electrical equipment.
– Remove the ignition key, if equipped.
– Remove the front door trim panel. Refer to ⇒ Body Interior;
Rep. Gr. 70 ; Front Door Trim Panels; Front Door Trim Panel,
Removing and Installing .
– Push the catches on the trim -1- for the Power Window Control
Head in Driver Door - E512- in the direction of the -arrow A-.
– Remove the trim -1- for the Power Window Control Head in
Driver Door - E512- in the direction of the -arrow B- from the
door trim panel.
– Release the hook -3- on both sides with a small screwdriver.
– Remove the Power Window Control Head in Driver Door -
E512- -2- from the trim -1-.
Installing
Install in reverse order of removal.
– Perform a function test.
2.20
Front Passenger Power Window Button
- E716- , Removing and Installing
Removing
– Turn off the ignition and all electrical equipment.
– Remove the ignition key, if equipped.
– Remove the front door trim panel. Refer to ⇒ Body Interior;
Rep. Gr. 70 ; Front Door Trim Panels; Front Door Trim Panel,
Removing and Installing .
– Release the hook in the direction of the -arrow A- with a small
screwdriver.
– Release the mounting tab -2- in the direction of the
-arrow B-.
– Remove the window regulator switch -3- from the switch
mount and remove it to the rear.
– Release and disconnect the connector -1-.
Installing
Install in reverse order of removal.
– Perform a function test.
2.21
Driver Interior Locking Button - E308- ,
Removing and Installing
Removing
– Turn off the ignition and all electrical equipment.
– Remove the ignition key, if equipped.
– Remove the Exterior Rearview Mirror Adjuster - EX11- . Refer
to
⇒ “2.18 Exterior Rearview Mirror Adjuster EX11 , Removing
– Release the retainers -arrows-.
– Remove the Driver Interior Locking Button - E308- -1- from the
Exterior Rearview Mirror Adjuster - EX11- -2- trim.
Installing
Install in the reverse order of removal while paying attention to
the following:
– The Driver Interior Locking Button - E308- must engage audi‐
bly in the trim for the Exterior Rearview Mirror Adjuster -
EX11- .
– Perform a function test.
2.22
Interior Monitoring And Vehicle Inclina‐
tion Deactivation Button - E616- , Re‐
moving and Installing
Special tools and workshop equipment required
♦ Trim Removal Wedge - 3409-
Caution
Risk of damaging the component surfaces.
♦ When positioning a prying tool, put commercially available
adhesive tape over the component in the visible area.
Removing
– Turn off the ignition and all electrical equipment.
– Remove the ignition key, if equipped.
– Pry out the Interior Monitoring and Vehicle Inclination Deacti‐
vation Button - E616- -1- using the -3409- or a screwdriver at
the lower edge.
– Remove the button from the B-pillar trim panel.
– Release and disconnect the connector -2-.
Installing
Install in reverse order of removal.
– Perform a function test.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст