Volkswagen 01M Transmission. Manual — part 105
7
4051 - 1 - 1
03C2T02168
Z
0
300 035H
09G
1004
32
1 6
C
A
49 BOLT 30 MM LENGTH (17 REQUIRED).
50 BOLT 45 MM LENGTH (1 REQUIRED).
51 BOLT 83 MM LENGTH (1 REQUIRED).
52 STUD BOLT 30 MM LENGTH (2 REQUIRED)
33. Remove the converter housing from transaxle
case by tapping with a mallet to loosen housing
from dowels and sealant (See Figure 66).
34. Set the converter housing aside for component
rebuild section.
31. Position transaxle so that converter housing is
facing up, as shown in Figure 64.
32. Remove the 21 converter housing bolts shown in
Figure 65, using a 12 mm socket or wrench.
Note: Converter housing bolt configuration
will vary depending on model and year. Some
locations have "stud" bolts (See Figure 65).
Continued on Page 51
TRANSAXLE DISASSEMBLY (CONT'D)
TRANSAXLE DISASSEMBLY (CONT'D)
Figure 65
Figure 66
Figure 64
{
{
1 Behind Bell
Housing Here
21 Total
2 Behind Bell
Housing Here
7
4051 - 1 - 1
03C2T02168
Z
0
300 035H
09G
1004
49
50
52
51
"B" = BOLT 83 MM LENGTH (1 REQUIRED).
"C" = BOLT 45 MM LENGTH (1 REQUIRED).
"A" = BOLT 30 MM LENGTH (17 REQUIRED.
B
A
A
A
A
A
A
A
A
A
A
A
A
C
A
A
A
A
D
D
50
Copyright © 2010 ATSG
Copyright © 2010 ATSG
AUTOMATIC TRANSMISSION SERVICE GROUP
Technical Service Information
WWW.ALL-TRANS.BY
7
4051 - 1 - 1
03C2T02168
Z
0
300 035H
09G
1004
32
6 1
C
A
35. Remove the six oil pump retaining bolts, as
shown in Figure 67.
Note: There are 3 different lengths and position
is critical. Label if necessary.
36. Remove the oil pump assembly, as shown in
Figure 67, and set aside for component rebuild.
Note: Number 1 thrust washer may be stuck
to back of oil pump (See Figure 67).
37. Remove and discard the three oil pump to case
gaskets, as shown in Figure 67.
Note: New design pump gasket with all three
gaskets mounted on steel core is included in
Trans-Tec® gasket set (See Figure 67).
38. Remove and discard the two case to converter
cover seals, as shown in Figure 67.
39. Measure the distance from case pump surface to
the washer surface on the K3 clutch housing, as
shown in Figure 68, using a straight edge and
ruler, or a depth micrometer.
Note: Record this measurement to use in the
reassembly process.
Continued on Page 52
TRANSAXLE DISASSEMBLY (CONT'D)
Figure 68
Figure 67
53 OIL PUMP RETAINING BOLT (22 MM LENGTH, 3 REQUIRED).
54 OIL PUMP RETAINING BOLT (30 MM LENGTH, 2 REQUIRED).
55 OIL PUMP RETAINING BOLT (25 MM LENGTH, 1 REQUIRED).
56 OIL PUMP TO CASE GASKETS (EARLY DESIGN).
61 CONVERTER COVER TO CASE SEALS (2 REQUIRED).
62 OIL PUMP ASSEMBLY.
73 OIL PUMP TO K3 CLUTCH HOUSING THRUST WASHER (NO. 1).
56
54
53
53
53
55
56
54
56
62
NEW DESIGN OIL
PUMP GASKET
61
61
73
51
Copyright © 2010 ATSG
Copyright © 2010 ATSG
AUTOMATIC TRANSMISSION SERVICE GROUP
Technical Service Information
7
4051 - 1 - 1
03C2T02168
Z
0
300 035H
09G
1004
3
4
5
1
2
S
t
t
ar
t
re
9
8
0
WWW.ALL-TRANS.BY
AU
FA
AU
FA
VW
G
A
VW
G
A
G
280
3
GZ
03
02
03C
8
2T
16
0
G
035
093
0
H
5
4 -
02
734
51
1
40
- 1
-
03
C
T
16
8
2
2
0
O
Z
0
0
3
0
5
3
H
9
0
G
04
10
136
137
140
138
139
Figure 70
Figure 69
Continued on Page 53
40. Remove the "rolled" pin from the inside detent
lever using a 3/16" punch and hammer, as shown
in Figure 69.
Note: There is a safety band around the inside
detent lever that must be removed first. Only
way to get it off is to break it and discard it.
The safety band will not be reused.
41. Remove the manual shaft from the top side of
the transaxle, as shown in Figure 70, by sliding
out through the inside detent lever and the case
bore.
42. Remove the inside detent lever and park rod, as
shown in Figure 70.
43. Remove and discard the manual shaft seal in the
case, as shown in Figure 70.
TRANSAXLE DISASSEMBLY (CONT'D)
7
4051 - 1 - 1
03C2T02168
Z
0
300 035H
09G
1004
136 MANUAL SHAFT SEAL.
137 MANUAL SHAFT.
138 ROLLED PIN.
139 INSIDE DETENT LEVER.
140 PARKING ROD.
52
Copyright © 2010 ATSG
Copyright © 2010 ATSG
AUTOMATIC TRANSMISSION SERVICE GROUP
Technical Service Information
WWW.ALL-TRANS.BY
7
4051 - 1 - 1
03C2T02168
Z
0
300 035H
09G
1004
420
100
111
113
7
8
4051 - 1 - 1
03C2T02168
Z
0
300 035H
09G
1004
Continued on Page 54
44. Remove the B1 clutch apply ring and return
spring assembly, as shown in Figure 71.
45. Remove the K3 clutch housing assembly, as
shown in Figure 71, and set aside for the
component rebuild section.
Note: Number 2 thrust washer may be stuck
to back of K3 clutch housing.
46. Remove the front planetary as an assembly, by
lifting assembly straight up using the input shaft,
as shown in Figure 72.
TRANSAXLE DISASSEMBLY (CONT'D)
53
Copyright © 2010 ATSG
Copyright © 2010 ATSG
AUTOMATIC TRANSMISSION SERVICE GROUP
Technical Service Information
Figure 71
Figure 72
100 K3 CLUTCH HOUSING ASSEMBLY.
111 NUMBER 2 THRUST WASHER.
420 B1 CLUTCH APPLY RING AND RETURN SPRING ASSEMBLY.
113 FRONT PLANETARY ASSEMBLY.
WWW.ALL-TRANS.BY
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст