Volkswagen Fox (2004 year). Manual — part 45
Carry out work sequence as follows:
– Place the wiper arm in the resting position.
– Remove the wiper blade.
– Place the wiper arm -2- on Adjustment device -3358B- and
fasten with the screw -3-.
– Check the incidence angle according to the following table:
Incidence angle (nominal values)
Driver's side
- 5,0°
Passenger's side
-5,0°
Tolerance
± 2,0°
If necessary, adjust the incidence angle to the nominal value as
follows:
– Place the Wrench -1- on the Adjustment device -3358B- and
move -arrows- the wiper arm -2- to the nominal value.
– Compare the adjusted value, as per the table. If necessary,
repeat the adjustment and control processes until reaching the
nominal value.
– Remove the Adjusting device -3358B- and install the wiper
blade.
– Check the wiper for smooth operation.
4.18
Tire pressure (including spare wheel),
condition, tread, sides and groove depth
- check
Note
For driving safety reasons, only tyres of the same type and profile
version must be installed on a vehicle!
4.18.1
Check the condition (including spare
wheel)
Carry out work sequence as follows:
FOX 2004 ➤
4. Service descriptions
53
move foreign bodies, such as nails and pieces of glass, for
example.
Note
In case of faults, please check if it is necessary to install a new
tire.
Inspection service:
– Check the tread, sides and groove depth for damage and, if
necessary, remove foreign bodies, such as nails and pieces
of glass, for example.
– Check the tyres for wearing, treads worn on only one side,
porosity on the toothed sides, cuts and perforations.
Note
The faults verified must be reported to the customer.
4.18.2
Check the treads (including spare
wheel)
From the front tire treads it is possible to evaluate, for example, if
there is the need to check the camber and convergence:
♦ The existence of burrs on the tire profile may be caused by
convergence failure.
♦ Tread wear on only one side can be mostly caused by camber
fault.
If there is such type of wearing, the cause must be determined by
measuring the axle geometry (repair measure).
4.18.3
Check the tyre profile depth (including
spare wheel)
– Check the groove's depth
A - Minimum groove depth -at-1.6 mm.
FOX 2004 ➤
54
4. Service descriptions
ches the indicators -position 1- at the bottom of the grooves.
The points where tread wear indicators are found are identified
by the acronym TWI (Tread Wear Indicators), distributed at every
60 degrees -a- on tire perimeter.
In this situation, the groove depth is approximately 1.6 mm. How‐
ever, considering that a worn tire is more likely to skid on wet
surfaces, we recommend replacing a tire when the groove depth
reaches 3 mm.
Note
♦
This value may be different depending on each country's legal
requirements.
♦
The minimum profile depth is reached when the wear indicator
at the tread, adjusted at 1.6 mm of height, no longer displays
a profile.
♦
If the profile depth is close to the legally accepted depth, the
customer must be informed.
♦
The tires must also be replaced when they are cut, deformed,
or display other damage.
4.18.4
Tyre pressure (including spare wheel) -
check and correct if necessary
Special tools and workshop equipment required
♦ Tire inflation device -VAS 5216-
FOX 2004 ➤
4. Service descriptions
55
♦
Please notice that the tire pressure values mentioned in the
table are valid for cold tires. Heated tyres should not be ex‐
cessively deflated.
♦
The pressure values for the respective model can also be
found on an adhesive tag located inside the fuel reservoir filling
nozzle compartment cover.
Note
On the CrossFox, the spare wheel has an anti-theft screw, which
socket is located on the tool bag.
4.18.5
Tyre pressure table
(for all sizes of tyres assembled in the factory)
Pressure values in PSI (pounds/sq-in)
Note
Values obtained at publishing date!
half load front and
rear
full load front and
rear
Engine identification letters AQZ, BJE, BNX, with mechanical
steering
175/65 R14 82T
31
27
33
39
Engine identification letters AQZ, BJE, BNX
175/65 R14 82T
29
28
31
36
185/60 R14 82H
30
29
33
37
195/55 R15 85H
27
27
28
33
Engine identification letters BAH, BJA, BPA
175/65 R14 82T
31
29
34
38
185/60 R14 82H
30
29
33
37
195/55 R15 85H
28
28
30
34
Engine identification letters BLH
185/60 R14 82H
30
29
33
37
Engine identification letters ASY
175/65 R14 82T
32
30
35
39
195/55 R15 85H
30
29
31
35
Engine identification letters BMD with mechanical steering
165/70 R14 81T
35
32
35
41
Engine identification letters BMD
165/70 R14 81T
29
28
32
38
185/60 R14 82T
29
28
32
38
195/55 R15 85V
28
28
30
36
Engine identification letters BKR
165/70 R14 81T
32
29
35
41
175/65 R14 82T
32
30
35
39
FOX 2004 ➤
56
4. Service descriptions
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст